Good Earth Lighting G9713-T5-WHES-I Guia De Inicio Rapido página 3

7
8
Fig. 10
9
leads from the fixture go to the white supply lead. Tighten the wire nuts properly to prevent the
wires from coming loose. Tape the wire nuts to the wire using electrical tape (Fig. 11). Carefully
push any excess wiring back inside the electrical box (Fig. 12).
10
11
12
Fig. 16
13
Bulb Replacement Instructions
Replace only with linear fluorescent bulb:
G9713-T5-WHES-I Bulb #F8T5;
G9725-T5-WHES-I Bulb #F14T5/CCT-3500K/120 volt/10,000 hour rated lamp life
fluorescent bulb;
G9734-T5-WHES-I Bulb #F21T5/CCT-3500K/120 volt/10,000 hour rated lamp life
fluorescent bulb.
Do not replace with any other wattage of linear fluorescent bulb. These
bulbs are readily available at your local home center and most larger hardware stores.
1
Fig. 1
2
Fig. 2
Insert the flexible whip or NM cable through the wire coupling
and tighten the clamp until it is secure (Fig. 9). Allow enough wire
length to make the connection. WARNING: Make sure the
Fig. 9
POWER is OFF.
Drill a 1/16 in. pilot hole into the marked screw locations. You
can also use an awl, or nail to dimple the screw
holes. Start the screws, but do not tighten fully. Slide the fixture
over until the narrow legs of the keyhole slots are under the
heads of the screws (Fig. 10). Finish tightening the screws until
they are firmly seated, and the fixture is tightly secured to the
mounting surface. Replace the diffuser.
For safety and proper operation, your fixture must be properly
grounded. If you are unfamiliar with the methods of properly
grounding your fixture, consult a qualified electrician. A copper
Fig. 11
ground wire is pre-attached to your fixture. If your electrical box
is made of plastic and/or has a green or has a bare copper
grounding wire inside, the fixture grounding wire and the
electrical box ground wire should be connected together using
one of the small wire nuts. If your fixture is being connected
using a flexible whip or NM cable the fixture grounding wire and
Fig. 12
the electrical supply ground wire should be connected together
using one of the small wire nuts. If your electrical box is made of
metal and is already grounded, secure the bare end of the fixture
ground wire to the crossbar using the green grounding screw on
the crossbar. Connect the supply leads from the electrical box to
the fixture wire leads using the medium sized wire nuts supplied
in your installation hardware kit as per the illustration. The black
leads from the fixture go to the black supply lead and the white
Align the lip on both ends with the slots on the fixture chassis
Fig. 13
Secure the fixture chassis cover by placing fingertips above
the locking tab on the face of the cover. Press on the cover
and lock the front edge under the locking tab (Fig. 15).
NOTE: You may have to engage each one individually before
it can be secured.
Fig. 15
Fig. 17
between the bulb pins and the socket contacts (Fig. 17).
Place the diffuser in the top lip. Push the grooved edge of the
diffuser down into the bottom edge until it locks in (Fig. 18).
Your installation is now complete. Restore power to the
electrical box.
Fig. 18
Remove the diffuser by pulling back and up on the top edge of
the diffuser using your fingertips (Fig. 1). When replacing a
defective bulb, use your thumbs to press and roll the bulb 90
degrees inside the socket. This will disengage the bulb contact
pins from the socket contacts. Then slide the bulb pins out of
the socket slot.
Install the bulb into the sockets by aligning the pins of the
bulb with the slot in the sockets (Fig. 2). Using your thumbs
and forefinger, press the metal ends of the bulb socket and
roll the bulb forward until it rotates 90 degrees inside the
socket, making contact between the bulb pins and the
socket contacts. Place the diffuser in the top lip. Push the
grooved edge of the diffuser down into the bottom edge
until it locks in. Restore power to the fixture.
then press on the cover and slip the edge
Fig. 14
under the clips (Fig. 13 & Fig. 14).
Install the bulb into the sockets by aligning the
pins of the bulb with the slot in the
sockets (Fig. 16). Using your thumb and
forefinger, press the metal ends of the bulb
socket, and roll the bulb forward until it rotates
90 degrees inside the socket, making contact
- 3 -