Specific Safety Instructions - NUTOOL NCD18 Manual De Instrucciones

Taladro atornillador de percusión sin cables
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 27
GB

2 SPECIFIC SAFETY INSTRUCTIONS

Be aware of the high torque reaction when drilling especially
when drilling masonry.
DO NOT try to change any of the selector switches while
the motor is running. Doing so could damage the machine.
DO NOT attempt to modify the machine or its accessories
in any way. DO NOT force the machine, let the machine
do the work. This will reduce the wear on the machine and
cutter and increase its efficiency and operating life.
Do not use this product with any attachment designed for
mixing mortar, concrete, or plaster. Or for any other type of
mixing operation.
ADDITIONAL SAFETY RULES FOR DRILLS
If possible, always use clamps or a vice to hold your work.
- Always switch off before you put the drill down.
- When using the drill, use safety equipment including
safety glasses or shield, ear defenders, and protective
clothing including safety gloves. Wear a dust mask if the
drilling operation creates dust.
ADDITIONAL SAFETY RULES CHARGERS
1 Before using the charger, read all the instructions and
cautionary markings on the charger and battery pack as well
as the instructions on using the battery pack.
2 Only charge your batteries indoors as the charger is
designed for indoor use only.
3 DANGER. If the battery pack is cracked or damaged in
any other way, do not insert it in the charger. There is a
danger of electric shock or electrocution.
4 WARNING. Do not allow any liquid to come into contact
with the charger. There is a danger of electric shock.
5 The charger and battery packs supplied with it are
specifically designed to work together. Do not attempt to
charge the battery pack with any other charger than the
one supplied.
6 Do not pull on the power cord to disconnect it from the
mains supply socket.
7 Do not use the charger if it has been subjected to a heavy
knock, dropped or otherwise damaged in any way. Take
the charger to an authorised service centre for a check or
repair.
8 Do not disassemble the charger. Take it to an authorised
service centre when service or repair is required.
Incorrect re-assembly may result in the risk of fire, electric
shock or electrocution.
9 To reduce the risk of an electric shock, unplug the charger
from the power supply before attempting to clean it.
Removing the battery alone does not reduce the risk..
ADDITIONAL SAFETY RULES FOR THE
BATTERY PACK
1 The battery pack for this tool has been shipped in a low
charge condition. You should charge the battery pack
fully before use.
2 Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery
pack can explode in a fire.
3 A small leakage of liquid from the battery pack may occur
under extreme usage or temperature conditions.
This does not necessarily indicate a failure of the battery
pack. However, if the outer seal is broken and this leakage
comes into contact with your skin wash the affected area
quickly with soap and water. If the leakage gets in your
eyes flush your eyes with clean water for a minimum of
10 minutes and seek immediate medical attention.
Inform the medical staff that the liquid is a 25-35%
solution of potassium hydroxide.
4 Never attempt to open the battery pack for any reason.
If the plastic housing of the battery pack breaks open or
cracks, immediately discontinue its use and do not
recharge it.
5 Do not store or carry a spare battery pack in a pocket or
toolbox or any other place where it may come into contact
with metal objects. The battery pack may be short-
circuited causing damage to the battery pack, burns or a
fire.
BATTERY CHARGING INFORMATION
Charging rates for NiCad and/or Li-Ion
NiCad and/or Li-Ion battery charging rates are determined
by the time taken to fully charge the battery and are
determined by the charge current. The three most commonly
used charging rates are typically:
Fast charge.
Slow charge.
Trickle charge.
Fast charge batteries
The charging rates for fast charge batteries can vary
between 30 minutes and 90 minutes. The charging rate for
the battery supplied with a cordless power tool is stated in
the product manual.
Slow charge battery
The charging rates for slow charge batteries are between 3
hours and 5 hours..
Trickle charge batteries
The charging rates for trickle charge batteries are between
7 hours and 9 hours..
IMPORTANT!
NiCad and/or Li-Ion battery charging information.
ALWAYS FULLY DISCHARGE A NiCad and/or Li-
Ion
BATTERY
BEFORE
EXCEED THE CHARGING RATE TIME, EXCEPT WHEN
"CONDITIONING" A NEW BATTERY
14
CHARGING
AND
NEVER

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Nchd18Nchd24Ncdl144Ncdl144-m

Tabla de contenido