Product Description And Specifications; Technical Data; Noise/Vibration Information - Bosch PSE 180 E Manual Del Usuario

OBJ_BUCH-746-002.book Page 11 Tuesday, June 19, 2012 9:26 AM
Safety Warnings for Electric Scrapers
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
Do not scrape wetted materials (e.g. wallpaper) or on
moist surfaces. Penetration of water into the machine in-
creases the risk of an electric shock.
Do not treat the surface to be worked with solvent-con-
taining fluids. Materials being warmed up by the scraping
can cause toxic vapours to develop.
Use extreme caution when handling blades. The appli-
cation tools are very sharp. Danger of injury.
Conduct the mains cable to the rear away from the pow-
er tool. Damage to the cable from sharp application tools
can lead to electric shock.
When working, wear safety goggles and protective
gloves. Danger of injury from chipping off or thrown about
material particles.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for partial removal and scraping off
of flooring material, adhesive, paint or filler remainders, for
smooting out irregularities, as well as for carving soft wood. It
is not suitable for removing tiles.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Blade*
2 Tool holder
Bosch Power Tools
3 Dust protection cap
4 On/Off switch with stroke rate preselection
5 Tool-lock button
6 Blade cover for extra-sharp blades
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Electric scraper
Article number
Rated power input
Stroke rate at no load n min
0
Stroke mm
Weight according to
EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 74 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a = 6.0 m/s , K= 1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
English | 11
PSE 180 E
0 603 316 7..
W 180
-1
6500/7500/8500
2
kg 0.9
/II
2 609 932 850 | (19.6.12)