Metra INSTXSVI-6523-NAV Guia De Inicio Rapido

INSTXSVI-6523-NAV
The following wires are for the aftermarket radios that have navigation built in.
• Connect the Light Green wire to the parking brake wire of the aftermarket
navigation radio (if applicable).
• Connect the Blue/Pink wire to the VSS or speed sense wire of the aftermarket navigation
radio (if applicable).
• Connect the Green/Purple wire to the reverse wire of the aftermarket navigation radio (if
applicable).
RCA CONNECTIONS
• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE back up
camera (if equipped).
• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to retain the OE
3.5mm jack (if equipped).
INSTALLING THE XSVI-6523-NAV
With the key in the off position:
• Connect the 16-pin and 12-pin harness into the interface.
• Connect the 52-pin harness into the vehicle.
Note: For the Fiat 500L and Ram Promaster City, do not perform this step yet.
• With all connections completed, reconnect the negative battery terminal
(including the Fiat 500L and Ram Promaster City).
Note: If using the ASWC-1, connect it after you initialize and test the XSVI-6523-NAV, with
the key in the off position.
INITIALIZING THE XSVI-6523-NAV
Attention: If the XSVI-6523-NAV loses power for any reason, the following step will need to be
performed again.
For the Fiat 500L and Ram Promaster City:
• Initialize the interface by first turning the hazard lights on.
• Connect the 52-pin harness into the vehicle.
• Turn the ignition on for 30 seconds, then turn the ignition back off, then back on again.
For all other models:
• Initialize the interface by turning the ignition on for 30 seconds, then turn the ignition
back off, then back on again.
K P
NOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
1-800-221-0932
REV. 8/31/2015 © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
metraonline.com
INSTXSVI-6523-NAV
XSVI-6523-NAV
Chrysler Data Interface 2013-up
• Provides accessory (12-volt 10 amp)
• Retains R.A.P. (retained accessory power)
• Used in non-amplified or amplified models
• Provides NAV outputs (parking brake, reverse, and V.S.S.)
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
• Retains back-up camera (if through the OE radio)
• Retains the use of the 3.5mm AUX jack
• High level speaker input
• Micro "B" USB updatable
APPLICATIONS
CHRYSLER JEEP
200 LX 2015-up
Cherokee Sport
DODGE
Renegade
Dart (small screen
RAM
option) 2013-up
1500, 2500, 3500 (small
FIAT
screen option) 2013-up
500L 2014-up
WIRING THE XSVI-6523-NAV
• Connect the Yellow wire to the radio's 12-volt battery or memory wire.
• Connect the Black wire to the radio's ground wire.
• Connect the Red wire to the ignition wire of the aftermarket radio.
• Connect the Orange wire to the illumination wire of the aftermarket radio. If the
aftermarket radio has no illumination wire, tape off the Orange wire.
• Connect the Blue/White wire to the amp turn-on wire of the aftermarket radio.
• Connect the White wire to the left front positive speaker output of the aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of the
aftermarket radio.
• Connect the Gray wire to the right front positive speaker output of the aftermarket radio.
• Connect the Gray/Black wire to the right front negative speaker output of the
aftermarket radio.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the Purple wire to the radio's right rear positive speaker output.
• Connect the Purple/Black wire to the radio's right rear negative speaker output.
1-800-221-0932
REV. 8/31/2015 © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Chassis cab 3500, 4500,
5500 (small screen option)
2014-up
2013-up
2015-up
Promaster
(with 5" screen or NAV)
2014-up
Promaster City 2015-up
metraonline.com