C- Installation Of Your Deep Freezer; Selecting The Place Of Installation; Positioning; Installation - Ugur UED 3094 DTK A+ Guia Del Usuario

C- INSTALLATION OF YOUR DEEP FREEZER

Selecting the place of installation

Ürününüzün sorunsuz bir şekilde çalışması için çalışacağı ortam çok önemlidir. Çalışma ortamını seçerken,
• The operating environment of the product is very important for the smooth operation of your product. While selecting
the operating environment,
• Do not place your product exposed to outdoor environment (on the street, avenue, roof, balcony etc.)
• Place the product at least one (1) meter away from heat resources (stove, radiator, electric heater etc.) (Picture 1)
• Do not place it opposite to the air conditioner chutes, under fans and direct door and window openings. (Picture 2)
• Do not expose to direct sunlight. Operation ratio will increase if sunlight comes to the freezer's glass. That means an
increase in the energy consumption.
• Be careful for not obstructing lower shutter of the product with materials such as cardboard, box etc. for a proper cooling.
• Air intake and outlet must absolutely be fluent and free for proper operation of the compressor section of your product.
• While approaching your product to the wall, be careful that there is a gap of 150 mm (15 cm) between the wall and back
of your freezer.
CAUTION!
In very humid environments, ensure that floor and wall of the place where the freezer is located, is not affected by
water; against discharge water overflow danger.
In installations performed by Authorized Uğur Service, Authorized Uğur Service shall inform the consumer on the
suitable place for installation and make suggestion, but the consumer shall give the final decision on where the
installation will be made. This above mentioned process shall also be stated on the relevant installation form by
Authorized Uğur Service. In case of any loss arising from the place of installation of the product according to the
final decision given by the consumer, all responsibility related to such loss shall belong to the consumer.
EN
Your cooler gives the best cooling performance according to the climate condition under the conditions given below.
Therefore, be careful that the temperature of the environment where your cooler will operate is at these levels.
In Domestic Products:
Climate Class Acceptable Ambient Temperature
Class T +16 °C to 43 °C
Class ST +16 °C to 38 °C
Class N +16 °C to 32 °C
Class SN 10 °C ile 32 °C
PICTURE 1
Climate Class of your product
is indicated on the technical
specification label on the
product.
PICTURE 2
42
C- INSTALLATION OF YOUR DEEP FREEZER

Positioning

Possible placement positions:
1- In a way that the back side alone is opposite to the wall; be careful that there is a gap of 150 mm (15 cm) between the wall
and your device. (Picture 3)
2- In a way that is place to a corner; when you place it to a corner, leave a gap of 150 mm (15 cm) behind. You can lean the side,
corresponding to the corner, to the wall.
The most important point to be considered in all cases of product placement is not to obstruct ventilation of the compressor
assembly.
Without exposing your product to any slope, place and operate it in a manner that it is on its feet or wheels.
The freer the compressor assembly ventilation is, the better the device will run.
PICTURE 3

Installation

Before positioning, remove and disassemble all packaging materials and bottom wooden pallet of the freezer. (It may
be necessary to lift the cooler for removing the bottom pallet).
Insert the replacement parts inside your product according to the installation instructions. Only use genuine Uğur
spare parts.
Inauthentic spare parts may constitute danger for you and damage your product.
Place the product anywhere you desire. Consider the placement rules written in the manual while positioning the
product.
Balance your product in width and in depth by means of a water gauge. Perform balancing operation by using adjus-
table feet at the bottom front of your cooler. (Picture 4)
In models with wheels (optional), wheel brake (optional) must be locked or if there is no wheel brake, it must be gua-
ranteed that the device will not move after the positioning of the product.
PICTURE 4
43
EN