Bell'O AVS-2752HG Instrucciones De Armado página 4

NOTE: TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS FURNITURE. IT SHOULD BE ASSEMBLED ON A SOFT, FLAT SURFACE.
1. PLACE the LOWER frame bars (1) and (2) UPSIDE DOWN with the two holes in the bottom facing up and the holes in the center of the sides ALIGNED.
IMPORTANT: The FRONT frame bars (1) and (5) have a hole in the rear side of the bar and NOT in the front side of the bar. The REAR frame bars (2) and (6) have a
hole completely through the bars. When positioned correctly, the holes will be ALIGNED when bars are attached to each other. NOTE THE PROPER DIRECTION OF THE
SLANT AT THE BAR ENDS AS SHOWN IN FIG. 1 DURING ASSEMBLY.
2. LOOSELY ATTACH one flat plate (3) with the recessed screw holes facing upwards to the two bottom frame bars, using the 1/4" x 15 mm funnel neck screws (4).
3. REPEAT this assembly for the UPPER frame bars (5) and (6). NOTE THE PROPER DIRECTION OF THE SLANT AT THE BAR ENDS AS SHOWN IN FIG. 1 DURING
ASSEMBLY
4. TURN the BOTTOM frame bars over so the plate (3) is sitting on the floor.
IMPORTANT: The next step is used to hold the furniture in place while securing the TOP frame bars. DO NOT SECURE THE LEGS TO THE BOTTOM FRAME BARS AT
THIS POINT. AVOID SCRATCHING THE LEGS OR THE BOTTOM FRAME.
5. ALL FOUR LEGS ARE THE SAME. PLACE the four legs (7), (8), (9), and (10) upright with the slots in the bottom of each leg over the BOTTOM frame bar as shown
in Fig. 1. The cut-out hole on the middle side of each leg MUST be facing OUTWARD away from the center of the table when fully assembled.
6. TURN the attached TOP frame bars (5) and (6) over so that the plate (3) is facing down toward the floor. PLACE the TOP frame bars into the slots on top of the legs.
LOOSELY SECURE the TOP frame bars to the legs with the 1/4" x 15 mm straight neck screws (13).
7. CAREFULLY LIFT the partially assembled table off of the BOTTOM frame bars and TURN the unit over so that it is resting on the TOP of the legs. The BOTTOM of the
legs will face up.
8. INSERT the CENTER shelf support bars (11) into the cutouts on the FRONT and REAR legs, with the curvature of bars facing OUTWARD as shown in Fig. 1.
NOTE: The REAR center shelf support bar (11) has two holes in the outward curve of the bar's flat side that should face the REAR when fully assembled. This is the
same direction as the holes in the REAR of the TOP and BOTTOM frame bars. The FRONT center shelf support bar (12) has NO holes in the bar's flat side.
9. CAREFULLY PLACE the BOTTOM frame bars into the slots in the legs with the plate (3) facing up. The holes in the flat side of the BOTTOM frame bar should face the
REAR. SECURE frame bars into the legs with the 1/4" x 15 mm straight neck screws (13).
10. NOW GO BACK AND TIGHTEN THE SCREWS THAT SECURE THE TOP AND BOTTOM FRAME BARS TO THE LEGS.
11. PLACE plastic caps (15) onto the bottom of the legs as shown in Fig. 2. FULLY TIGHTEN the flat plate (3) to the two bottom frame bars and CAREFULLY TURN the
unit over so that it is upright. PLACE plastic caps (15) onto the tops of the legs as shown in Fig. 2.
12. The REAR of the TOP and BOTTOM frame bars have a hole drilled in the center of the bars where the FRONT and REAR frame bars meet. From the REAR, PLACE a
washer (14) over the hole in the TOP frame bars. Use the OPEN END WRENCH, to SCREW the shorter threaded end of the LONG tie bar (16) through the REAR of
the TOP frame bar and into the FRONT TOP frame bar until tight. REPEAT this tie bar (16) assembly for the BOTTOM frame bars.
13. PLACE a washer (14) over the exposed ends of the LONG tie bars (16). POSITION the open side of the CMS
REAR with the two screw holes in the TOP of the CMS
against the REAR center shelf support bar (11). ATTACH the rear of the CMS
EN AT THIS POINT.
14. SECURE the LONG tie bars (16) to the rear of the of the CMS
15. GO BACK and FULLY TIGHTEN the CMS
16. MOVE the table to the location that it will occupy when fully assembled and in use.
17. PLACE glass pads (22) onto the left, center and right tops of the BOTTOM, TOP and CENTER shelf support bars as shown in Fig. 1.
18. PLACE the TOP (largest) shelf (23) onto the TOP bars with the two silver discs facing the rear and into the holes in the top of the CMS
silver discs to the CMS ® frame with the 1/4" x 25 mm screws (19).
19. CAREFULLY PLACE the smaller shelves (24) onto the BOTTOM and CENTER shelf Support frames with the holes in the shelves facing towards the REAR. INSERT
the shelves through the slots in the CMS
IMPORTANT: REMOVE ALL GLASS, TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT. DO NOT ATTEMPT TO MOVE
THE ASSEMBLED FURNITURE AFTER THE GLASS SHELVES HAVE BEEN INSTALLED, AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS
MAY CAUSE THE SHELVES TO BECOME UNSECURED AND FALL. MAKE SURE THAT THE FRONT OF THE TV IS POSITIONED A FEW INCHES BACK FROM THE FRONT
OF THE TOP GLASS. WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT AND LEVEL SURFACE. ALWAYS PLACE THE HEAVIEST EQUIPMENT ON THE
BOTTOM SHELF.
® frame facing up. SLIDE the CMS
® frame with 1/4" x 16 mm OPEN ended screws (18).
® frame to the table frame and the flat plate (3) to the two top frame bars.
® frame. LOCK the shelves in place with the T-shaped pins (20) through the holes in the rear of the shelves.
English
® frame over the ends of the LONG tie bars (16) so that it is resting
® frame (25) to the support bar with 1/4" x 60 mm screws (17). DO NOT FULLY TIGHT-
® (Cable Management System) frame (25) facing the
® frame (25). SECURE the