XPG PYLON BRONZE Serie Guia De Inicio Rapido página 8

INSTALLING YOUR NEW PYLON POWER SUPPLY
Make sure that your system is turned off and unplugged before you start installing it.
Disconnect the AC power cord from your old power supply if any.
1. Remove the power supply from its packaging.
2. Install the PSU into the case with the four screws provided.
3. Connect the 24pin ATX cable to the motherboard 24pin power socket.
4. Connect the EPS 12V 8 / 4+4pin cable to the CPU power socket.
5. Connect SATA power cables to any devices that may use 4-pin peripheral connectors, i.e. hard drives, solid state
drives, optical drives.
6. Connect the corresponding PCI-E connector as instructed by your graphic card's user manual, if your graphic card
requires additional PCI-E power.
Please note that the power supply utilizes a 6+2pin PCI-E connector that can be effectively used either as a single
8pin or a 6pin PCI-E connector.
To use it as a 6pin PCI-E connector, please detach the 2pin connector portion from the
7. Connect the peripheral/floppy disk 4pin connector for fans, pumps, legacy components and other devices/adaptors.
8. Connect the AC Power cord to both your power supply and to the wall.
Check all connections to ensure that every item is properly plugged in and turn the power switch of the power supply
to the ON position.
TROUBLESHOOTING
If your system does not turn on after installing the power supply, please follow the
troubleshooting guide listed below:
1. Please make sure the AC main power cord is connected to your PC correctly and that your power outlet is properly
emitting power.
2. Please make sure the AC On/Off switch on the back panel of the power supply unit in the "I" (On) position.
3. Please make sure that the MB& CPU Power Socket & connectors are connected correctly on the motherboard.
4. If you still have problem turning on your PC, please contact ADATA Tech Support, Service Center or your local dealer.
DURATION OF WARRANTY
ADATA Technology Co., Ltd. provides a 3 years warranty period for this product unless
regional laws and regulations state otherwise.
LIMITATION OF WARRANTY
This limited warranty covers only repairs or replacements of products manufactured by
ADATA Technology Co. Ltd. and its authorized partners.
Please note that ADATA is responsible for providing free repairs except for the following
reasons:
1. The warranty label is altered, damaged or missing.
2. Product serial number does not conform to our original system.
3. Product was purchased from an unauthorized agent.
4. Damage caused by natural calamity
5. Any abuse outside the intended product operation.
ONLINE CUSTOMER SERVICE
For frequently askeatd questions, additional information and service instruction please visit
our product page www.xpg.com
connector header.
13
IMPORTANT SAFETY INFORMATION
1. NEVER, under any circumstances, open the power supply unit or attempt to repair it by yourself. This is extremely
dangerous due to the high voltage components inside.
2. DO NOT insert any object into the fan grill or the ventilation area of the power supply unit.
3. DO NOT place any object in front of the fan or the ventilation area of the power supply unit that may obstruct or
restrict airflow.
4. USE the included cable with the power supply unit. or as purchased from XPG. DO NOT use any third party cables
or extension cables with this unit.
5. Avoid dust, humidity, and temperature extremes. Do not place the power supply unit in any area where it may
become wet.
6. The power supply unit is for integration into a computer, and not intended for external or outdoor usage.
7. Failure to comply with any manufacturer instructions and/or any of these safety instructions may result void
warranties and guarantees.
SAFETY AND AGENCY APPROVALS
Agency
EN55032:2015, EN55035:2017, EN IEC 61000-3-2:2019,
CE
EN 6100-3-3:2013+A1:2019
IEC 62368-1:2014 (Second Edition)
CB
IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013
FCC Part 15 Subpart B Class B:2020
FCC (IC) ICES-003 Issue 6:2016
ANSI C63.4:2014
TP TC 004/2011
EAC
TP TC 020/2011
CCC
GB4943.1-2011, GB17625.1-2012, GB/T9254-2008
TUV
EN 62368-1:2014
UL 62368-1:2014
cTUVus
CAN/CSA-C22.2 No. 62368-1-14
TUV-S
IEC 62368-1:2014
RCM
IEC 62368-1:2014, US-TUVR-012145
NOM
NOM-001-SCFI-1993
BSMI
CNS15663第五節(102), CNS13438 (95), CNS14336-1 (99)
KC
K60950-1 (2011-12)
2011/65/EU & 2015/863/EU, Restriction of Hazardous Substances
ROHS 2.0
Directive
WEEE
2012/19/EU Waste electrical and electronic equipment Directive
Standard
14