Electrical Safety - Black and Decker KG2000 Manual Del Usuario

ENGLISH
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
O
read the instruction manual.
Wear safety glasses or goggles when operating this
N
tool.
Wear ear protection when operating this tool.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Side handle
5. Spindle lock
5. Guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (fig. A)
The tool is supplied with a guard intended for grinding
purposes only. If the unit is intended to perform cutting off
operations, a guard specific for this operation must be fitted. A
suitable guard for cutting off operations part number 1004484-
03 is available and can be obtained from Black & Decker
service centres.
Fitting
Place the tool on a table, with the spindle (6) facing up.
u
Hold the guard (5) over the tool as shown.
u
Align the holes in the adjusting plate (7) with the screw
u
holes (8).
Press the guard down and insert the screws (9) into the
u
holes.
Tighten the screws.
u
Removing
Remove the screws (9).
u
Remove the guard from the tool.
u
8
(Original instructions)
Warning! Never use the tool without the guard.
Adjusting the guard (fig. B)
The guard can be rotated 180°.
Slacken the screws (9) and the nut (10).
u
Rotate the guard as required.
u
Re-tighten the screws and the nut.
u
Fitting the side handle
Screw the side handle (3) into one of the mounting holes
u
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs (fig.
C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data). The maximum thickness for grinding discs is 6
mm, for cutting discs 3.5 mm.
Fitting
Fit the guard as described above.
u
Place the inner flange (11) onto the spindle (6) as shown
u
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (6) as shown (fig. D).
u
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner
u
flange.
Place the outer flange (14) onto the spindle. When fitting
u
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. E). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. E).
Keep the spindle lock (4) depressed and tighten the outer
u
flange using the two-pin spanner (15) (fig. F).
Removing
Keep the spindle lock (4) depressed and loosen the outer
u
flange (14) using the two-pin spanner (15) (fig. F).
Remove the outer flange (14) and the disc (12).
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Be prepared for a stream of sparks when the grinding or
u
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
u
provides optimum protection from the grinding or cutting
disc.