Troubleshooting; Technical Specifications - RIB WIND Instrucciones Para El Uso Y La Instalacion

Pag. 32 di 44
Release the door and switch on the system. The computer starts up and measures the opening width.
Wait approx. ten seconds for the system to warm up, after which the sensors start functioning. Ensure that the door opens and closes correctly.
Switch off the system and open the door/s manually.
WARNING: Do not switch the system off while the door is moving.
The door/s must be open and closed manually. Once the power is restored, the door/s automatically resume normal operation.
If an electric lock is installed with manual release, activate the release cable before moving the door.
Never pass through the entrance from the side as the sensors do not operate in this area. We recommend putting a notice or obstacle to prevent accidents. If a person comes into contact
with the door/s the latter automatically inverts the direction of movement and opens completely. After 2 seconds the sensor is re-activated and the door/s close automatically.
Photocells must be fixed to the sides of the door to protect the door opening area.
Photocells re-open the door and keep it open for the time that an obstacle engages the infrared range.
Any strong vibration or impact with the door/s during movement can cause malfunctions. Never STOP or PUSH the door intentionally.
Before transferring goods thought the doorway or before cleaning the door, switch off the system and open the door/s manually.
WARNING: Take care when opening the door/s manually to avoid crushing hands/fingers.
Check that no water penetrates sensors, photocells or the actuator during cleaning.
The door/s will not slide smoothly if dirt builds up in the floor guide. Clean regularly and remove any stones/leaves when found.
In the event of a problem, refer to the following table before contacting technical assistance.
PROBLEM
A) The door/s does not open
B) The door/s does not close
C) The guide makes a metallic noise
In the event of any problem, always switch off the system before maintenance and switch on after eliminating the problem.
If the problem persists following checks, switch off the system and call your authorised RIB dealer. Abnormal noise during operation indicates incorrect door operation. DO NOT ATTEMPT
ELECTRONIC REPAIRS ALONE.
Service
Power supply
Max. door weight
Max. door opening
Door opening speed
Door closing speed
Wait time on automatic closing
Manual force (less than 110 N) applied to open door in event
of power failure
Motor output
Microcomputer
Drive system
Impact
Assembly type
Track material
Drive belt material
Adjustable attachments
Safety system to reverse direction of movement
Adjustable wait time before automatic closing
USER MANUAL
BEFORE USING THE PRODUCT
KEEPING THE DOOR OPEN
IN THE EVENT OF A POWER FAILURE
MAINTENANCE AND SAFETY PRECAUTIONS
ACCIDENT PREVENTION
CORRECT USE OF THE AUTOMATIC DOOR
CLEAN THE FLOOR GUIDE REGULARLY

TROUBLESHOOTING

CAUSE
A) The door/s has been locked. The door cannot be
opened manually if locked.
No power supply.
The sensor is not working and the indicator is switched
off.
B) Sensor/s or photocells do not work due to dust or
internal humidity
C) Dirt, dust, or stones are in or on the floor guide

TECHNICAL SPECIFICATIONS

Continuous
230V ~ 50/60 Hz
Single leaf: 30Ö150 kg
Double leaf: 30Ö150 kg per leaf
30 cm Ö 3 m
100 mm/s Ö 440 mm/s per leaf
100 mm/s Ö 440 mm/s per leaf
0.5 s to 10 s
3 kg or less (door weight 70 kg)
5 kg or less (double leaf, 70 kg per leaf)
50 W (with starting torque engaged on acceleration)
built-in
electric motor coupled to reduction gear
built-in software to absorb impact of door (with inversion of travel)
wall-mounted
6n¡1.T5
high resistance belt: SUPER TORQUE 120S8M R8K 009
Standard models
OTHER FUNCTIONS
REMEDY
A) Release the door/s.
Switch on the system.
Refer to the instructions supplied with the sensor.
B) Refer to the instructions supplied (dry the sensor/s or
photocells with a cloth)
C) Clean the guide with a vacuum cleaner and apply oil to
the guide.