Black+Decker BDBV30 Manual De Instrucciones página 9

Slide the second handle (12) in place over the buttons
u
(15).
Note: Ensure that the orange button is is on the same side as
the large hole in the handle.
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the position of the second handle (fig. C)
(GW3030 BDBV30 only)
The second handle (12) can be adjusted to provide optimum
balance and comfort.
Press in the button (15) on the left side of the handle.
u
Rotate the second handle (12) into the required position.
u
Release the button (15).
u
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Blow tube assembly (fig. D)
Align the 2 markers (16) on bottom of the upper blow tube
u
(4) and the 2 markers (17) on the bottom of the lower blow
tube (5).
Push the upper blow tube (4) firmly into the lower blow
u
tube (5) until they click into place.
Warning! Do not separate the tubes once assembled.
Fitting and removing the concentrator (fig. D)
Slide the concentrator (30) firmly onto the bottom end of
u
the lower blow tube (5). Secure the concentrator by cliping
the tab (31) onto the clip (32)
To remove, lift the clip (32) and slide the concentrator (8)
u
off the bottom of the lower blow tube(5).
Fitting and removing the rake (fig. E)
(GW3050,BDBV30 &GW2838 only)
Position the rake (18) above the mount (19) on the bottom
u
of the lower blow tube (5).
Push down and slide the rake (18) firmly onto the mount
u
(19) until it clicks into place.
To remove, lift the rake release (20) and slide the rake
u
(18) off the mount (19).
Use
Switching on and off (fig. F)
Warning! Grip the product firmly when switching on.
To switch the appliance on, turn the variable speed control
u
(1) clockwise to the required setting.
To switch the appliance off, turn the variable speed
u
control (1) anti-clockwise to the off position.
Cable restraint (fig. G)
A cable restraint (2) is incorporated into the rear of the
powerhead.
(Original instructions)
Loop the cable (21) through the cable restraint (2).
u
Using your product
Warning! When using as a blower or vacuum, always wear
safety glasses. If using in dusty conditions, wear a filter mask
as well.
Warning! Switch off your product, allow the fan to stop and
remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Blow mode (fig. H and I)
Attach the fan cover (22) to the powerhead (11) by
u
locating the assembly as indicated by the arrow, then pivot
about this point and press the vac release button (9) until
the catch (23) is fully engaged. (fig. H)
Align the assembled blow tube with the power head (11).
u
Push the assembled blow tube onto the vacuum outlet
u
(25) until the lock engages tightly with the blow tube.
Warning! Never operate in Blow mode without the blow tube
and fan cover firmly in place.
Hold the blow tube approximately 180 mm above the
u
ground, switch on the appliance and using a sweeping
motion from side to side, advance slowly keeping the
accumulated debris/leaves in front of you (fig. I).
Once you have blown the debris/leaves into a pile, you
u
can convert to vacuum mode to collect the debris.
Removing the blow tube and fan cover
Remove the fan cover (22) from the bottom of the power
u
head by inserting a screwdriver/Allen key in the slot on
the end of the fan cover (located on the back of the power
head) to actuate the internal release, and remove the fan
cover (figure H).
Vacuum mode (fig. H, J & K)
Note: For vacuuming/shredding, the collection bag (3) must
be fitted.
Remove the fan cover (22) by pressing the vac release
u
button (9) and pulling the fan cover (22) off, making sure
that the fan cover does not fall to the ground.
Attach the collection bag (3) to the vacuum outlet (25) by
u
pressing it firmly on till it clicks into place.
Attach the assembled vacumm tube to the powerhead (11)
u
by locating the assembly as indicated by the arrow, then
pivot about this point and press the vac release button (9)
until the catch is fully engaged.
Place the strap from the collection bag over your shoulder
u
(fig. K) this will support the additional weight as the
collection bag fills. Alternatively the collection bag can be
clipped to the support bracket (28 - fig. A) on the upper
vacuum tube (4) and the strap can be fitted to the
powerhead (11) on the hook (29).
ENGLISH
9