Publicidad
Idiomas disponibles
Idiomas disponibles
READ INSTRUCTIONS IN CONJUNCTION WITH THE
ILLUSTRATIONS
IMPORTANT
1.THE FAN MUST BE SITED AND CONNECTED
IN
ACCORDANCE
WITH
REGULATIONS (UK) OR THE APPROPRIATE
STANDARDS IN YOUR COUNTRY.
2.THIS APPLIANCE IS NOT SUITABLE FOR
INSTALLATION IN A SHOWER CUBICLE OR
ENCLOSURE AND MUST BE SITED AWAY FROM
ANY SOURCE OF WATER SPRAY, AND MUST BE
OUT OF REACH OF A PERSON USING A FIXED
BATH OR SHOWER.
3.SITE AWAY FROM DIRECT SOURCES OF
HEAT IN EXCESS OF 50ºC.
4.WHEN THE FAN IS INSTALLED IN A ROOM
CONTAINING A FUEL BURNING APPLIANCE,
THE INSTALLER MUST ENSURE THAT AIR
REPLACEMENT IS ADEQUATE FOR BOTH THE
FAN AND THE FUEL BURNING APPLIANCE. IF
THE FAN CAN BE USED TO SUPPLY AIR INTO
THE ROOM THE INSTALLER MUST ENSURE
THAT THE FAN INTAKE IS LOCATED AT LEAST
600mm AWAY FROM ANY FLUE OUTLET.
5.WIRING SHOULD BE VIA A SWITCHED SPUR
WITH A 3 AMP FUSE. (UK ONLY.)
6.DOUBLE POLE SWITCH OR PLUG AND
SOCKET SHOULD BE LOCATED OUTSIDE THE
ROOM
CONTAINING
A
FIXED
SHOWER.
7.THIS APPLIANCE MUST BE EARTHED.
8.READ THESE INSTRUCTIONS FULLY BEFORE
COMMENCING INSTALLATION
9.IF A T-SERIES CONTROLLER IS TO BE USED,
IT IS ESSENTIAL TO WIRE WITH 5-CORE
CABLE
10.THE APPLIANCE IS NOT INTENDED FOR
USE
BY
YOUNG
CHILDREN
PERSONS WITHOUT SUPERVISION.
11.YOUNG
CHILDREN
SUPERVISED TO ENSURE THAT THEY DO NOT
PLAY WITH THE APPLIANCE.
VOLTAGE
A.Check rating label to ensure that the motor is the correct
voltage. (see A).
WHERE TO FIT
BA short circuit of the airflow should always be avoided by
siting the fan as far away as possible from and opposite to the
main source of air replacement.
FAN DIMENSIONS
C1i/C3iiBefore commencing work, study the tables shown in
figures C1i/C3ii, to ensure fan will fit in position proposed.
PREPARATION AND INSTALLATION
Fitting Panel Model
C4iiYour T-Series Panel Model is suitable for fitting in vertical
or horizontal surfaces.
Cut the hole to the dimensions given in Table C4ii.
Fitting Wall Model
C2iYour T-Series Wall Model is suitable for fitting in most
double brick and cavity walls from 240mm upwards. The two
sections of the liner are designed to accommodate thickness of
wall up to 315mm. Further liner sections are available as an
accessory for walls of greater thickness. Cut the hole through
the wall to the dimensions given in Table C2i.
D1From outside, fit the section of liner with brackets on the
large end, flush with the outside wall face (ribs at the bottom,
cable entry at the top).
D2From the inside, cut out the cable/conduit entry on the
remaining section of liner. Fit the liner with brackets on the
small end flush with the inside wall face, (ribs at the bottom,
cable entry at the top). Feed through wiring from the T-Series
Controller (5-core cable) or on/off switch (3-core cable). There
should be sufficient cable within the liner to allow for the
connector socket to be wired up and for the unit to be
withdrawn.
D3Cement the two wall liners into place taking care not to
distort the sides.
D4Fit the exterior louver to the exterior grille frame. Engage
the bottom edge first then lock into position by twisting the turn
buttons. Remove the fixing screw covers from the grille frame
and fix the grille to the outside of the liner using the four screws
provided. Ensure that the grille louvers are slanting downwards.
Note:
The frame recesses are marked A and B, and
correspond with the covers.
Replace the screw covers (A's and B's must match).
Wall and Panel Models
E1Place fan unit, impeller downwards, on a flat surface.
Unscrew grille securing screw located at the top of the grille.
E2Remove grille.
Partially unscrew the two safety catch
screws on the face of the housing.
E3Depress the side catches.
E4Lift off the housing.
E5If the unit is to be wired through a T-Series Single Unit
Controller, the speed control pack must be removed from
the unit and plugged into the T-Series Controller. (See
Controller Fitting and Wiring Instructions). If the unit is to be
wired through an on/off switch, it can be preset at one of three
speeds. It is factory set for high speed (Position III). If the
CURRENT
IEE
medium speed is required, remove speed control pack and insert
it in Position II, if low speed is required insert in Position I.
E6Replace housing with connector slot uppermost.
E7With the two side catches fully engaged, tighten the catch
safety screws.
E8Replace interior grille with louvers slanting upwards.
Engage the bottom edge first, then push the top home. Tighten
the securing screw at the top of the grille.
E9Place grille frame downwards on a flat surface. Place fan
housing assembly with the grille locating in the frame,
orientated as shown. Loosen the four frame clamp screws, and
attach the two clamps. Ensure the tongues under the clamp
heads engage in the slots on the housing.
E10Tighten the four screws.
WARNING THIS APPLIANCE MUST BE EARTHED
WIRING THE CONNECTOR SOCKET
F1Remove the top cover from the connector socket by undoing
the 2 retaining screws.
F2Lift up lever and slide out top cover.
F3Loosen cable clamp screws and pass the cable through the
clamp. (It may be necessary when using some 3-core cables to
reverse the cable clamp to ensure that the cable is securely
retained.
Note:
If the unit is to be wired through a T-Series single unit
BATH
OR
controller, strip wires of the 5-core cable, see controller wiring
instructions for connections, and continue from F6. Check if
wiring through an on/off switch for single speed extract or
intake use, strip wires then connect to a suitable 3 pin plug or, if
permanently wired, a double pole isolator switch having a
contact separation of not less than 3mm must be provided.
For extract operation
F4Connect Live (brown) to terminal L3, Neutral (blue) to
terminal N and Earth (green/yellow) to terminal E/G in the
connector socket. Link terminal L3 to L1.
For intake operation
OR
INFIRM
F5Connect Live (brown) to terminal L3, Neutral (blue) to
terminal N and Earth (green/yellow) to terminal E/G in the
SHOULD
BE
connector socket. Link terminals L3 to L2.
F6"Click" terminal block into the base of the connector socket,
then tighten cable clamp screws evenly, ensuring a secure grip
on the outer sheath of the cable.
F7Slide the top cover back on and secure with the 2 retaining
screws.
F8Partially place the complete fan assembly into the wall and
push connector socket lever down to lock it in position.
Remove the fixing screw covers. Fix the fan on to the inside
liner, with the louvers slanting upwards, using the fixing
screws. Replace the screw covers.
Note:
Performance guide in m
Wall Model 240V / 1 / 50Hz
SIZE
6
7
9
12
Panel Model 240V / 1 / 50Hz
SIZE
6
7
9
12
FOR THE USER
CLEANING
Apart from removing odours, your Vent-Axia fan also extracts
airborne impurities such as dirt, dust and grease.
gradually build up and detract from the efficiency and
appearance of your fan.
designed for easy cleaning and maintenance. Therefore, to
ensure peak performance of your fan it should be regularly
cleaned.
IMPORTANT: SWITCH OFF AND ISOLATE UNIT FROM
MAINS SUPPLY.
The A's and B's must match.
3
/h and max watts input
HIGH
MEDIUM
LOW
WATTS(on
395
350
270
530
435
335
870
755
515
1745
1530
1185
HIGH
MEDIUM
LOW
WATTS(on
435
380
295
585
480
365
960
830
565
1885
1640
1270
The Vent-Axia T-Series fans are
Dismantling
Disconnect mains supply.
G1Remove the four fixing screw covers on the indoor grille
frame and unscrew. Note: In the frame recesses are marked A
and B, and these correspond with the covers.
G2Partially remove the fan and disconnect the connector socket
by raising the lever gently with a finger.
G3Remove the outdoor grille from inside ready for cleaning by
twisting the turnbutton at the top.
G4Loosen the clamping screws and remove the clamps.
G5Remove the fan from the frame.
G6Remove the grille.
G7Partially unscrew the two safety catch screws on the face
housing, depress the two side catches.
G8Lift off the housing.
G9Ease back motor support safety catch to the left of the
connector socket opening. Rotate motor support assembly anti-
clockwise and withdraw it.
G10Remove impeller with a sharp pull.
Cleaning
IMPORTANT:
KEEP ELECTRICAL COMPONENTS
AWAY FROM WATER
G11Wall model only – wipe inside of wall liners with a damp
cloth.
G12Wipe motor and housing assembly with a damp cloth.
G13Wash all non-electrical parts in warm water and detergent.
Re-assembly
G14Align marks on impeller with drive pin on motor shaft.
With a sharp push, replace impeller back onto motor shaft.
Ensure that the impeller snaps into position.
G15Wall model only – replace grille from inside, engaging the
bottom edge first. Make sure the grille louvers are slanting
downwards. Lock in position by twisting the turn-button at the
top.
G16Replace motor support assembly and turn it clockwise until
the safety catch is fully engaged.
G17Replace housing.
G18Ensure that the two side catches are fully engaged. Tighten
the catch safety screws.
G19Replace the interior grille with the louvers pointing
upwards. Engage bottom edge first then push the top home.
Tighten grille securing screw.
G20Place the grille frame downwards.
position and re-assemble the two frame clamps.
G21Partially place the complete fan assembly into the wall
liner, supporting weight by holding main housing – not the
grille frame. Replace connector socket by pushing the lever
down to lock it in position.
G22Fix the fan onto the inside of the wall liner, with the
louvers slanting upwards, using the fixing screws, and replace
the screw covers. Note: The A's and B's must match.
Switch on supply and check fan function.
The motor in this Vent-Axia product is fitted with sealed-for-
life bearings and therefore does not require lubrication.
WARNING
DO NOT INSTALL A YELLOW SPEED CONTROL PACK
INTO A GREY SOCKET OR VICE VERSA.
WARNING
high)
IF USING A T-SERIES CONTROLLER, THE YELLOW SPEED
30
CONTROL PACK MUST BE REMOVED FROM THE UNIT
AND INSTALLED INTO THE CONTROLLER.
40
85
Available Controllers
105
For single fans up to 100 watts:
For multiple fan applications up to 400 watts:
high)
30
40
85
105
These
Locate the unit in
W30 01 20 (Ecotronic 130)
W36 11 19 (TSC Controller)
W36 23 20 (Ecotronic 400)
Publicidad
