Video Setup - Rotel RSP-1576 Manual De Instrucciones

26
OFF TIMER: Set the amount of time the units stays powered on when there
is no audio signal. The RSP-1576 will automatically go to standby mode
if audio is not detected for the specified timer period. Default: 20 MINS.
Valid settings include: Disable, 20 MINS, 1 Hour, 2 Hours, 4 Hours.
MAX POWER ON VOLUME: Specifies the maximum volume level to be
used each time the unit powered on. Valid settings include: 20 - 70.
Default: 45.
POWER MODE: Enables the rear panel USB power port to remain
powered at all times. The power consumption is higher in Quick Power
mode. To enable continuous power to the rear USB power port select
the Quick option.
Valid settings include: Normal, Quick.
NOTE: When the POWER MODE is configured to Quick, the RSP-1576
will consume additional power in standby mode.
SIGNAL SENSE INPUT: Checks if a digital audio signal is present on
the configured Signal Sense Input. When this input is selected as the
active listening source, the RSP-1576 monitors the digital data stream to
determine if there is audio. If there is no audio detected for 10 minutes,
the RSP-1576 will enter Signal Sense Standby Mode. When in Signal
Sense Standby Mode and the RSP-1576 detects audio on Signal Sense
Input, the unit will automatically power on. To disable this function, select
the DISABLE option which is the factory default setting.
NOTE: The Signal Sense function is not available if Standby Video
Source is enabled.
NOTE: When the RSP-1576 enters standby mode via the remote
control, the Signal Sense function will not operate until the unit detects
the audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.
NOTE: When the SIGNAL SENSE INPUT function is activated, the
RSP-1576 will consume additional power in signal sense standby mode.
NETWORK CONFIGURATION: Sets the network configuration for the unit. In
most systems, set the IP ADDRESS MODE to DHCP. This setting will allow
your router to assign an IP address to the RSP-1576 automatically. If your
network uses fixed IP addresses, set the IP ADDRESS MODE to Static. A
fixed or STATIC IP address requires manually entering the IP Address, Subnet
Mask, Gateway, and DNS in the IP ADDRESS CONFIGURATION sub menu.
NETWORK CONFIGURATION
IP ADDRESS MODE
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK
DHCP
RSP-1576 Surround Sound Processor
SOFTWARE INFORMATION: Displays the current software installed in the
unit. It shows the MAIN, DSP and STANDBY software versions. There is also
an option to check for software updates. This feature lets the unit search
for software updates on the Internet. The network needs to be properly
configured. Alternatively, you can load the software through the front USB
socket. For more information on the software update process please contact
your authorized Rotel dealer.
RESTORE FACTORY DEFAULT: This option sets the unit back to the original
setting as when it left the factory. All user settings will be erased.
NOTE: Use caution when resetting the RSP-1576 to factory defaults
as all user configured options will be erased and reset to original
factory settings.

Video Setup

VIDEO SETUP
STANDBY VIDEO SOURCE
FAST AUDIO SYNC
OSD FORMAT
BACK
The VIDEO SETUP menu provides configuration of the HDMI outputs. See
the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI
connections.
STANDBY VIDEO SOURCE: Options are "Disable", "HDMI 1-6", "HDMI
Front", or "Last". This allows the selected HDMI source input to pass-through
the RSP-1576 while in standby mode. Audio and video are passed directly
to the attached TV or display.
NOTE: When the Standby Video Source is enabled the RSP-1576 will
consume additional power when in standby mode.
NOTE: Signal Sense power control is disabled with STANDBY VIDEO
SOURCE is enabled.
FAST AUDIO SYNC: This function allows the HDMI audio to sync more
quickly with the RSP-1576. Only 1 input can be selected for this function.
NOTE: Some source devices do not provide the timing requirements to
allow this function to work properly and could result in static noise before
the audio is heard.
OSD FORMAT: The HDMI On Screen Display output resolution can be
changed from 480p to 576p. The default value is 480p.
Press the BACK button or select "BACK" on the OSD to exit the VIDEO
SETUP Menu and return to the main menu.
Disable
Disable
480P