Ryobi EDP-5530L Manual De Utilización página 23

GB
F D
RULES FOR SAFE OPERATION
A guard or other part that is damaged must be
properly repaired or replaced by an authorized
service center to avoid risk of personal injury.
USE THE RIGHT DIRECTION OF FEED. Feed work
■
into a blade, cutter, or sanding spindle against the
direction or rotation of the blade, cutter, or sanding
spindle only.
NEVER LEAVE TOOL RUNNING UNATTENDED.
■
TURN THE POWER OFF. Don't leave tool until it
comes to a complete stop.
PROTECT YOUR LUNGS. Wear a face or dust mask
■
if the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing
■
protection during extended periods of operation.
DO NOT ABUSE CORD. Never carry tool by the cord
■
or yank it to disconnect from receptacle. Keep cord
from heat, oil, and sharp edges.
USE OUTDOOR EXTENSION CORDS. When tool is
■
used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
STAY ALERT AND EXERCISE CONTROL.
■
Watch what you are doing and use common sense.
Do not operate tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN
■
IT ON AND OFF. Have defective switches replaced
by an authorized service center.
ALWAYS TURN SWITCH OFF before disconnecting
■
it to avoid accidental starting.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
■
Normal sparking of the motor could ignite fumes.
INSPECT TOOL
■
If damaged, have repaired by a qualified service
technician at an authorized service facility.
The conductor with insulation having an outer surface
that is green with or without yellow stripes is
the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to
a live terminal. Repair or replace a damaged or worn
cord immediately. Stay constantly aware of cord
location and keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY
■
and replace if damaged.
GROUND ALL TOOLS. If tool is equipped with
■
threeprong plug, it should be plugged into a three-
hole electrical receptacle.
E I P NL
CORDS PERIODICALLY.
S DK N FIN
English
USE ONLY CORRECT ELECTRICAL DEVICES:
■
3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the
tool's plug.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL
■
AND GREASE. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any solvents to clean tool.
NEVER START A TOOL WHEN ANY ROTATING
■
COMPONENT IS IN CONTACT WITH THE
WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
■
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING use only identical replacement
■
parts. Use of any other parts may create a hazard or
cause product damage.
USE ONLY RECOMMENDED ACCESSORIES listed
■
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
IF THE POWER SUPPLY CORD IS DAMAGED,
■
it must be replaced only by the manufacturer or by an
authorized service center to avoid risk.
KEEP BITS CLEAN AND SHARP. Sharp bits
■
minimize stalling. Dirty and dull bits may cause
misalignment of the material and possible
operator injury.
KEEP HANDS AWAY FROM WORK AREA.
■
Keep hands away from the bit. Restrain any loose
clothing, jewelry, long hair, etc., that may become
entangled in the bit.
ALWAYS CLAMP WORKPIECE AND BRACE
■
AGAINST COLUMN TO PREVENT ROTATION.
Never use your hand to hold the object while drilling.
USE RECOMMENDED SPEED FOR DRILL
■
ACCESSORY AND WORKPIECE MATERIAL.
BE SURE DRILL BIT OR CUTTING TOOL IS
■
SECURELY LOCKED IN THE CHUCK.
BE SURE CHUCK KEY IS REMOVED from the
■
chuck before connecting to power source or turning
power ON.
ADJUST THE TABLE OR DEPTH STOP TO AVOID
■
DRILLING INTO THE TABLE. Shut off the power,
remove the drill bit, and clean the table before
leaving machine.
AVOID DIRECT EYE EXPOSURE when using the
■
laser guide.
15
GR H CZ RUS RO PL