Honeywell HeatGenius HCE840 Serie Manual De Usuario página 3

10. Warning – This appliance has a polarized plug
(one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this
safety feature.
11. Warning – This heater draws 12.5 amps
during operation. To prevent overloading a
circuit, do not plug the heater into a circuit
that already has other appliances working.
12. Warning – It is normal for the plug to feel
warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug
may cause overheating and distortion of the
plug. Contact a qualified electrician to replace
loose or worn outlet.
13. Warning – To disconnect the heater, first turn
off the product, then grip the plug body and
pull it from the wall outlet. Never pull by the
cord.
14. Warning – DO NOT insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric shock
or fire, or damage the heater.
15. Warning – To prevent a possible fire, do not
block air intakes or exhaust in any manner.
DO NOT use on soft surfaces, like a bed, or
where openings may become blocked.
16. Warning – A heater has hot and arcing or
sparking parts inside. DO NOT use it in areas
where gasoline, paint or flammable liquids are
used or stored.
17. Warning – Use this heater only as described in
this manual. Any other use not recommended
by the manufacturer may cause fire, electric
shock, or injury to persons.
ABOUT CERAMIC TECHNOLOGY
• Ceramic heaters generate heat by passing electricity through heating wires embedded in ceramic plates.
• In the Honeywell HeatGenius Ceramic Heater, air is drawn into the back of the heater by two fans,
TM
through the ceramic elements and out the front of the heater to gently introduce warm air into the room.
• This type of heating technology provides consistent, even heating.
• For best results, place heater on the floor and allow heater to run for 5-10 minutes to reach maximum
heat output.
2
18. Warning – Always plug heater directly into
a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap
(outlet/power strip).
19. Warning – Never tamper with this product
or attempt to fix it. Any tampering with, or
modification of this product can result in
serious injury, death, or fire. Risk of electric
shock. DO NOT open. There are no user
serviceable parts inside.
20. Warning – DO NOT remove product labels
that contain warnings or safety instruction.
21. Caution – The output of this heater may vary
and its temperature may become intense
enough to burn exposed skin. Use of this
heater is not recommended for persons with
reduced sensitivity to heat or an inability to
react to avoid burns.
22. Caution – Before cleaning, or storage, or when
not in use, turn the product's controls to the
OFF position and unplug the heater from the
electrical outlet and allow to cool.
23. Caution – Place the heater on a firm, level,
open surface free from obstructions and at
least 3 feet (0.9 m) away from any combustible
materials. DO NOT use on an unstable surface
such as bedding or deep carpeting. Be sure
the heater is not in a position where it may be
tripped over by small children or pets.
24. Caution – If your home has aluminum
wiring have a licensed electrician check your
receptacle's connections. When using a 1500
watt heater, aluminum wire connections can
cause a safety issue.
SAVE THESE
25.
INSTRUCTIONS
SET UP
• The Honeywell HeatGenius Ceramic Heater requires no assembly. Simply unpack heater and save all
TM
packaging materials for off-season storage.
• Place the heater on a firm, level, open surface, free from obstructions and at least 3 feet (0.9 m) away
from any wall or combustible material.
• DO NOT use on an unstable surface such as bedding or deep carpeting.
• BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY CHILDREN OR PETS.
MOVING THE HEATER
• Turn off the heater.
• Allow it to cool for ten minutes.
• Unplug heater and move it to desired location. This heater is equipped with a Cool Touch handle for your
convenience.
OPERATION
Fig. 1
Whole Room Heat Settings
(Constant Hi/Lo)
Personal Space
Heat Settings
Floor
Area Heat
Setting
Power
Button
• NOTE: NEVER LEAVE AN OPERATING UNIT UNATTENDED
• With heater in the OFF position ( ), plug the heater into a polarized 120V outlet. DO NOT FORCE THE
POLARIZED PLUG INTO THE OUTLET; it will only fit one way.
• The Honeywell HeatGenius Ceramic Heater is designed to be placed at least 3 feet away from the wall,
TM
allowing for convection room heating and safer operation.
• Turn heater on by pressing the Power Button ( ).The Power Indicator will light and the heater will start in
the Constant HI Room Setting (Hi).
NOTE: Because the Low settings do not require as much electricity to operate, they are more energy
efficient and may be a better option if you are concerned about saving energy.
• When done using this appliance, make sure the power to the heater is OFF.
• To shut the heater off, press the Power Button ( ) and the heater will begin Powering Down. The heater will
shut off after counting down 6 seconds in the Temperature Display to cool down the internal components.
Make sure that the power button light is NOT illuminated to confirm that the heater is OFF.
• See next section for overview of heat settings.
2 Hour Auto-off Timer
Desired Temperature
with 30 minute
Display
phased intervals
Low Heat &
White Noise
Setting
Thermostat
Control Buttons
3