Cadence Option; Installing The Battery In The Computer - VDO X Serie Manual De Instrucciones

D GB F I

3.2 Cadence option

The cadence menu is only available if
the cadence transmitter is installed,
B
the transmitter was recognized during pairing.
B
After pairing the cadence transmitter, the current ca-
dence is shown in section 2 of the display.
In function mode it is possible to select the CADENCE/
MORE menu using the using the up/down
buttons.
4 Installation
4.1 Fitting the transmitter, magnet and handlebar holder
Start by fitting the transmitter and magnet.
ATTENTION: The transmitting distance between
the transmitter and the computer on the handle-
bars should not be more than 60 cm (transmission
range).
step 1 Place the rubber pad under the transmitter.
Fit the transmitter on the same side of the fork
where you later want to fit the computer to the
handlebars (right or left) using the cable ties sup-
plied (loose at first, do not pull tight just yet).
ATTENTION: The sensor mark on the transmitter
must point to the spokes.
Depending on the room available, the transmitter
can be fitted at the front on the forks, inner side
of the fork or backside of the forks. >>> P04
28 X1DW
Confirming with M opens the menu and gives you
access to the information.
Using you come to:
AVG CADENCE
B
MAX CADENCE
B
Resetting the trip data also sets the cadence data
back to zero.
>>> P01
step 2 Place spoke magnet around an outer
spoke. The silver middle of the magnet points
towards the transmitter. Align the magnet to the
sensor mark on the transmitter with a gap
of about 1 – 5 mm.
Step 3 Align transmitter and magnet for good and
fasten in place: Pull cable ties tight and push
magnet in firmly.
Step 4 Decide whether fitting to handlebar or
stem and turn the base of the handlebar holder
by 90° accordingly. To do so, undo the screws in
the holder, take out the foot and turn it 90°, insert
and tighten the screws again.
ATTENTION: Do not over tighten screws.
VDO CYCLECOMPUTING
step 5 Guide the cable ties through the slot in the
handlebar holder, place around the handlebars
or the stem and pull (do not pull tight just yet).
4.2 Switching on the computer for the first time
Waking up from despatch mode
The computer is delivered with a battery installed.
To reduce the battery consumption, the computer
is put into despatch mode. The display is empty
(no display).

4.3 Installing the battery in the computer

Your VDO computer is supplied with a 3V battery
(type 2032).
The battery is already installed when supplied.
To change the battery, proceed as follows:
step 1 Place the battery in the computer casing
with the +terminal facing up.
Step 2 Make sure that the battery does not
get wedged.
step 3 Take care that the rubber seal lies flat on
the battery compartment lid.
Step 4 Insert the battery compartment lid into the
opening and turn it with a coin to the right as far
as it will go (approx. 1/3 turn).
www.vdocyclecomputing.com
I F GB
Step 6 If fitting to handlebar: Align computer
angle to achieve optimum readability. Now pull
cable ties tight. Snip off protruding ends with
clippers.
>>> P02, Display see Chapter 5.1
To wake it up out of despatch mode, press the
button simultaneously for a few seconds.
The computer is now ready for use and tells you
so by showing the language setting.
See also Chapter 5.1
>>> P05
TIP for changing battery: VDO recommends chang-
ing the battery once a year. Buy a new battery in
good time to ensure the wireless transmission
works perfectly. When the battery is changed,
all settings and the total kilometres cycled
are saved.
X1DW
D
29