Stanley STHT0-77365 Manual Del Usuario página 3

• NEVER intentionally short any battery
terminals.
• DO NOT attempt to charge alkaline
batteries.
• DO NOT dispose of batteries in fire.
• ALWAYS remove the battery if storing the
unit for over a month.
• DO NOT dispose of this product with
household waste.
• ALWAYS check local codes and properly
dispose of used batteries.
• PLEASE RECYCLE in line with local
provisions for the collection and disposal of
electrical and electronic waste.
WARNING:
• Carefully read the User Safety and
Operating Instructions before
using this product. The person responsible
for the instrument must ensure that all
users understand and adhere to these
instructions.
WARNING:
• The following labels are placed on the laser
tool to inform you of the laser class for your
convenience and safety.
OPERATING INSTRUCTIONS
BATTERY
Open the battery door on the handle of unit
and connect 2 AAA (1.5 V) batteries, ensuring
polarity is correct per the indication on the
inside of case. Replace battery door. It is
recommended to replace the batteries with
new batteries when battery indicator shows
USAGE
1. Point the IR Thermometer at the object
• When the trigger is released 3 audible
2. When the IR Thermometer is in the "ON"
Distance
1cm@8cm
Distance
2cm@16cm
3. When the IR Thermometer is in the "ON"
3cm@24cm
Distance to spot size = 8:1
2cm@16cm
3cm@24cm
Distance to spot size = 8:1
SCAN HIGH
NORMAL
LOW
°C
°F
4. When the IR Thermometer is in the
REF
SCAN
3cm@24cm
REF
Distance
2cm@16cm
3cm@24cm
5. Press the
3cm@24cm
Distance to spot size = 8:1
3cm@24cm
SCAN HIGH
NORMAL
LOW
Distance
REF
• To disable the threshold feature, press the
1cm@8cm
2cm@16cm
3cm@24cm
Distance to spot size = 8:1
6. Once a reference temperature and
SCAN HIGH
NORMAL
LOW
°C
°F
REF
3cm@24cm
to be measured, pull and hold the
trigger. When the IR thermometer is in
measurement mode the LCD backlight
will illuminate and the laser will be on, the
measurement indicator "SCAN" icon will
also be displayed on the LCD.
beeps will sound and the laser will shut off;
the last temperature reading will remain
on the LCD. After 15 seconds the LCD
backlight will turn off and after 1 minute the
IR Thermometer will turn off.
state (trigger is not pulled), pressing the
button will select the desired unit of
º C/ º F
SET
measure: C° or F°.
º C/ º F
SET
state (trigger is not pulled), pressing and OFF
1cm@8cm
holding the button for about 3 seconds
OFF
will turn the unit off.
Distance
HIGH
NORMAL
LOW
measurement mode (trigger is pulled and
°C 1cm@8cm
2cm@16cm
°F
Distance to spot size = 8:1
º C/ º F
held), pressing the
Distance
Distance
SET
º C/ º F
reference temperature.
SET
1cm@8cm
1cm@8cm
2cm@16cm
button to select the desired
SCAN HIGH
1cm@8cm
NORMAL
2cm@16cm
LOW
Distance to spot size = 8:1
°C
Distance to spot size = 8:1 OFF
temperature threshold (0.5°C/1°F, 3°C/5°F, °F
REF
or 5.5°C/10°F). The
SCAN HIGH
NORMAL
º C/ º F
current setting.
SCAN HIGH LOW
°C
NORMAL
°C
LOW
°F
SET
°C
°F
°F
REF
REF
button until the
OFF
"OFF" mark.
temperature threshold are set the unit
can be used to scan areas for changes in
temperature. While in measurement mode
the backlight will be green and "NORMAL"
1cm@8cm
2cm@16cm
Distance to spot size = 8:1
OFF
SCAN HIGH
NORMAL
LOW
°C
°F
REF
º C/ º F
SET
button will set the
º C/ º F
OFF
SET
OFF
OFF
icon indicates your
icon is over the
.
3