Instruction Manual - VERTO 52G505 Manual Del Usuario

GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
ELECTRIC BLOWER
52G505
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
DETAILED REQUIREMENTS FOR THE ELECTRIC LEAF BLOWER
WARNING: Observe safety regulations when using the device. For
your own and other people's safety please read this manual before
starting work. Keep the manual for future reference.
INSTRUCTION
• Before use, inspect the unwound power cord for signs of damage or
wear.
• Do not use the device if the power cables are damaged or worn out.
• Before connecting to the power source, always make sure the supply
voltage is compatible with the value specified on the nameplate of
the tool.
• The device can be connected only to electrical system equipped with
differential current protection that will cut the power off when earth
leakage current exceeds 30 mA in less than 30 ms.
• To connect the tool, use a power cord suitable for outdoor use.
• Immediately disconnect the power, if the power cord is damaged
during operation. DO NOT TOUCH THE POWER CORD, before it is
disconnected from the power supply.
• WARNING: The turbine keeps on turning, after the motor is stopped.
• Keep the unwound power cord away from the suction tube.
• Do not allow the tool to be operated by children and people not
familiarized with the instruction manual.
• Stop working, when other people, especially children or pets are
nearby.
• REMEMBER: The operator or user is responsible for accidents or
hazards occurring to other people or the environment.
PREPARATION
• Always wear sturdy shoes and long trousers during operation.
• Do not wear loose clothing that can be sucked into the suction tube.
Keep long hair away from air intakes.
• Always use personal protective equipment, such as safety glasses and
hearing protection.
• Check thoroughly the area you are going to work on and remove all
items that can be sucked into the suction tube or blown away by the
air blower.
• Do not begin working without air tubes, safety devices and covers
installed in place.
• Hold the tool with both hands so the end of the pipe is not obstructed
by the ground.
• Attach the extension cord to prevent its accidental disconnection.
USE
• Work only in daylight or good artificial light.
• Avoid sucking in water.
• Always make sure that your legs stand firmly on a slope.
• Walk, never run.
• Pay particular attention when changing sucking or blowing direction.
• When moving the tool, turn it off.
• Do not use the tool, if the pipe is damaged or not attached.
• Make sure the vents are free from dirt or debris.
• Before starting the tool, make sure that you are firmly holding the tool
handle.
• Pull the plug out of mains socket:
– every time you walk away from the device;
– before inspecting, cleaning or repairing the device;
– after the device has been struck by a foreign object - check if it is
not broken;
– if it begins to vibrate excessively;
• The tool should be repaired by authorized personnel only.
• Use only original spare parts recommended by the manufacturer.
MAINTENANCE AND STORAGE
• Keep all components in good condition to make sure that the tool will
work safely.
• For safety reasons, replace worn or damaged parts.
• Protect the tool from moisture.
• Keep out of reach of children.
Explanation of pictograms used
1 2
6 7
11 12
1. Read all instructions
2. Use safety glasses and ear protection
3. Use protective clothing
4. Use protective gloves
5. Watch out for people in the tool operating range
6. Protect from rain
7. Disconnect before repair (maintenance)
8. Risk of fingers cut-off by rotating rotor blades
9. Keep a distance
10. Watch out for debris
11. Warning
12. For use outdoors
13. Do not touch moving parts of the machine
14. Do not allow children to the tool
CONSTRUCTION AND USE
The electric blower is a hand device with Class II insulation. It is driven
by a single-phase AC commutator motor. The electric blower is a two-
function device designed for blowing and sucking in the around the
house and garden. It is perfect for cleaning and removing leaves, mown
grass from patios, paths and roads. This device is not designed for
industrial applications and indoor use.
The device cannot be used for other purposes than it is intended for.
DESCRIPTION OF GRAPHIC PAGES
The enumeration below refers to the parts of the device shown in the
graphic pages of this manual.
1. Blowing connector
2. Switch
3. Switch lock button
4. Suction connector
5. Nozzle
6. Collection bag
7. Carbon brush plug
* The actual product may differ from the drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Nozzle
2. Dust bag
8
3 4 5
8 9 10
STOP
13 14
– 1 pcs.
– 1 pcs.