Technical Data; Attachment And Operation - Scheppach LB5200BP Las Instrucciones Originales

Risidual risks
Even if used properly, residual risks can exist even if
the relevant safety regulations are complied with due
to the design determined by the intended purpose.
Observing these instructions, and taking proper care,
will reduce the risk of personal injury or damage to
the equipment.
• Injury by catapulted parts.
• Breaking or catapulting of knife pieces.
• Carbon monoxide poisioning when using the de-
vice in closed or poorly ventilated rooms.
• Burning when touching hot parts.
• Impairment of hearing when working on the ma-
chine for longer periods of time without ear pro-
tection.
In addition, in spite of all the precautionary measures
taken, non-obvious residual risks can still exist. Re-
sidual risks can be minimised if the "Safety informa-
tion" and the "Intended usage" as well as the whole
of the operating instructions are observed.

6. Technical data

Dimension L x W x H
Air speed max.
air volume max.
Power unit
Displacement
Max. engine output
Idle speed
Fuel tank capicity
Engine type 2-stroke engine, air-cooled
Weight
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 94,0 dB(A)
pA
Sound power L = 110 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A = 1,655 m/s
2
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
1380 x 400 x 450 mm
295 km/h
18 m /min
3
51,7 cm
3
1,4 kW
3500 ± 300 min
-1
1000 cm
3
7,84 kg
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Attachment and operation

ATTENTION! Before working on the device - clean-
ing, inspection, maintenance or other work - always
turn off the device.
Assembly (Fig. 6 - 6c)
m WARNING: The blower must not be used or
switched on until it has been fully assembled.
• Attach the two hose clamps (17A and 17B) to the
flexible blowpipe (12).
• Push the flexible blowpipe (12) over the connection
to the motor unit and tighten the hose clamp (17B)
firmly (Fig. 6).
• Now push the handle (1) over the upper blowpipe
(13). Align the handgrip (1) and the guide in the
same way, fold it together and then tighten it (Fig.
6a).
• Push the upper blowpipe into the flexible blow hose
(12) with the handle and fix it with the hose clamp
(17A) (Fig. 6b).
• Push the lower blowpipe (14) over the upper blow-
pipe (13) and lock it in the clockwise direction (Fig.
6c)
• The blower nozzle (No. 15) is simply pushed over
the lower blowpipe (No. 14) and locked in the clock-
wise direction (Fig. 6c).
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Operation
Before starting
Place the carrying strap
Pull the belt down, the straps are tightened
Loosen the straps
Lift the clamping slide
Adjust the carrying strap so that the back plate rests
firmly and securely against t
Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are com-
plete.
• That all screws are securely fastened.
GB | 23