BLACK&DECKER ASI200 Manual De Instrucciones página 5

When the item to be inflated has reached the preset
value the unit will automatically turn off.
To turn the inflator off press switch (5) to the 0 position.
Remove the valve adaptor or accessory from the
inflated item and the 12 Volt adapter (6) from your
vehicle's 12 Volt accessory socket.
Note: If the 12 Volt adapter is removed from the vehicles
12 Volt accessory socket, all settings will be lost and will
need to be re-entered following the instructions under the
heading 'Setting the required pressure'.
Operating the area light
To operate the area light (1), make sure that the 12 Volt
adaptor (6) is plugged into the vehicle's 12 Volt
accessory socket.
Note: Make sure that your 12 Volt accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
To turn the area light on, press the area light on/off
switch (7) located on the side of the unit to the I position.
To turn the area light off, press the area light on/off
switch (7) located on the side of the unit to the 0
position.
To replace the bulb (fig. E)
Warning! Make sure that the 12 Volt adaptor is not
connected before starting this procedure.
Remove the screw (10) from the top of the lens
cover (12).
Pull the lens cover (12) down using the tab (11) to get
access to the bulb (13).
To remove the bulb, push in and turn clockwise (fig. E).
Replace the bulb (13) with a one of the same type and
wattage (12V/5W).
Fit the lens cover (12) and secure with the screw (10).
Using your inflator as a pressure gauge
Make sure that the unit is powered as described in the
section 'Operating the Inflator'.
Connect the universal valve adaptor and accessories if
required to the item to be inflated making sure that the
lever of the valve adaptor is in the down position to lock
it in place.
The display will now show the actual pressure value in
the item.
Maintenance
Your Black & Decker corded/cordless appliance/tool has
been designed to operate over a long period of time with
a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and
then switch off.
Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust from
the interior (when fitted).
Troubleshooting
Problem Possible cause
Inflator will not 12 Volt adaptor
operate not connected
Accessory socket
not live
No preset
valve set
The fuse in the
12 Volt adaptor
is blown
Cord or switch is
damaged.
Replacing the fuse in the vehicle dc accessory plug
Remove the cap by turning it counter-clockwise.
Loosen the cap and centre pin.
Remove the fuse.
Fit a new fuse of the same type and size (8A/250V).
Refit the cap and centre pin.
Tighten the cap by turning clockwise onto the plug.
ENGLISH
Possible solution
Connect the 12 Volt
adaptor
Turn key to accessory
position
Set preset value
Replace the fuse with
one of the same size
and type (8A/250V)
Have the cord or
switch replaced at a
Black & Decker Service
Centre or Authorized
Service Centre.
5