Electrical Safety - Skil F0150700 Serie Manual Original

Ocultar thumbs Ver también para F0150700 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29
Weed brush
INTRODUCTION
• This tool has been designed for removing weed from
terraces and between tiles
• This tool is not intended for professional use
• Check whether the packaging contains all parts as
illustrated in drawing 2
• When parts are missing or damaged, please contact your
dealer
• Read this instruction manual carefully before use
and save it for future reference 3
• Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious injury
TECHNICAl DATA 1
TOOl ElEmENTS 2
A Cutting guard
B Wheel
C Spindle-lock button
D Collet nut
E Wrench
F Brush
G Brush indicator
H Locking sleeve
J Telescopic tube
k Handle
l Cord restraint
m Trigger switch
N Ventilation slots
P Storage rail (screws not supplied)
SAFETY
SPECIFIC SAFETY INSTRUCTIONS FOR WEED
BRUSHES
GENERAl
• Be familiar with the controls and the proper use of the tool
• The user is responsible for accidents or hazards
occurring to other people or their property
• Only use the tool when the ambient temperature is
between 0°C and 40°C
• Never mount metal cutting elements onto this tool
• Do not use the tool for removing wet weed
PERSONAL SAFETY
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the tool by a person responsible for their safety
• Ensure that children do not play with the tool
• Never allow children or people who are not familiar with
the operating instructions to use the tool
• Always wear eye protection, long trousers and sturdy
shoes when operating the tool
• Never operate the tool with a damaged cutting guard or
without the cutting guard mounted
• Never operate the tool in the direct vicinity of persons;
0700
stop using the tool when persons (especially children) or
pets are nearby
• Never operate the tool when you are tired, sick or under
the influence of drugs, alcohol or medication

ElECTRICAl SAFETY

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Inspect the cord periodically and have it replaced by a
qualified person, if damaged
• Inspect the extension cord periodically and replace it, if
damaged (inadequate extension cords can be
dangerous)
• Only use an extension cord which is intended for outdoor use
and equipped with a watertight plug and coupling-socket
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
• Do not run over, crush or pull the (extension) cord
• Protect the (extension) cord from heat, oil and sharp
edges
• Keep the (extension) cord away from the rotating brush
• Always switch off tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
BRUSHES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Only mount brushes of which the maximum speed
("RPM") is higher than the rotations per minute marked
on the tool
• Only use brushes with a maximum diameter of 100 mm
• Do not use worn brushes
• Rust stains or other signs of chemical or mechanical
changes of the material that hold the brush threads may
cause premature brush disfunctioning
• Store brushes in a suitable place in such a way that they
are protected against the following influences:
- high atmospheric humidity, heat, water or other fluids
which could damage the brush
- acids or acid vapours, which could damage the brush
- low ambient temperatures causing condensation on
the brush when stored in an area with higher ambient
temperatures
- deformation of whatever part of the brush
BEFORE USE
• Only use the tool in daylight or with appropriate artificial
lighting
• Check the functioning of the tool before each use and
after any impact; in case of a defect, have it repaired
immediately by a qualified person (never open the tool
yourself)
• Remove any adjusting key or wrench before turning the
power tool on (a wrench or a key left attached to a
rotating part of the power tool may result in
personal injury)
6

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

F0150700agF0150700 aaF0150700 ac

Tabla de contenido