Cleaning; Storing - Hydas 4657.1.00 Instrucciones Servicio

• Insure that the low voltage cable (5) that leads from the controller is properly plugged into the
plug on the upper surface of the heating blanket (6)
• Plug the Tranformer into the wall socket (8) and the transformer cable into the controller (7).
3. TURNING ON AND USE OF THE CARBON HEATING BLANKET (pict. 3)
ON/OFF SWITCH:
The on/off switch 1 on the bottom of the controller provides it with current
• In the „0" position no current is provided to the controller
• In the „1" position current is supplied to the controller and the red LED
i In the setting „1" the controller does not supply the blanket with current, it is only in stand-
by mode
TIMER: BUTTONS 2 3
- ACTIVATION:
Button (+) of the timer 2 allows the activation of the heating function. By depressing and hol-
ding the button (+) on the timer (3 seconds), the heating is turned on with 1 hour set on
2
the timer.
- SETTING THE TIMER:
Depressing button (+) multipe times allows to select the duration of heating time
2
from 1 to 9 hours. Depressing button (-)
ting duration.
- DEACTIVATE - STANDBY MODE:
By depressing and holding button (+)
blanket is turned off . The standby mode is thereby activated and the red LED light
is lit.
- AUTOMATIC SHUT OFF
The heating blanket turns itself off after the set time runs out. The standby mode is
thereby activated and the red LED light
HEATING LEVELS: BUTTONS 4 5
Depressing buttons and allows one to select among one of 4 heating levels.
4 5
Upon turning on the unit the heating level is automatically set to level 1. The desired he-
ating level may be selected by depressing button
(Heating level -)
i
For overnight or extendend use, the heating level 1 should be selected. The bed will be comfortably warm after approx. 40 minutes of
preheating. In colder environments preheating may need to be extended to 1 hour.
- RAPID HEATING
The system has a function named „BOOST" for speed heating of the heat blanket. To activate it press button
4 LED lights up the heating buttons
the "BOOST" function may not be reused until the next restart.
- AUTOMATIC HEAT CONTROL
The system also has an automatic heat control system. When heat level is set to 2, 3 or 4, it automatically reduces itself to level 1 after 2 hours of
use.
- TURN OFF THE DEVICE
Always use the switch on the bottom of the controller to turn off the unit. Set it to position „0" and remove the plug from the wall socket.
1

4 | Cleaning

• To clean the heating blanket, do not use a carpet beater or steam cleaner.
• Take note of the tag on the heating blanket containing washing instructions.
CAUTION!
Never immerse the controller in water. You should occasionally clean it with a soft, damp cloth. Do not use gasoline, glass
cleaner, furniture polish or paint thinner.
Machine washing: The Carbon heating blanket may be washed on gentle at 90 degrees farenheit
Handwashing: The Carbon Heating blanket may be hand washed maximally at 90 degrees farenheit. Use gentle liquid laundry detergent in
accordance with manufacturers instructions.
• Do not spin. Do not wring out.
• Washing is recommended only when dirty. Washing too frequently will reduce the life expectancy of the product.
• Do not wash the Carbon heating blanket when damaged.
Drying: Only air drying. The product must not be dried in the dryer.
• To prevent yellowing or other color changes, minimize exposure to direct sunlight.
• Insure the clthespins are not fastened to electical parts.
• Do not use the carbon heating blanket until it is completely dry.
Inspect the heating blanket for possible damage. Please contact the retailer for repair.

4.1 | Storing

• Store in a clean, dry place
• Insure the device is completely cool before folding and stowing
allows to return to previously selected hea-
3
2 (3 seconds), the mode of the Carbon heating
6 is lit.
4 (Heating level +) or button
4 are activated. After approximately 20 minutes the heating level automatically reduces to level 1 and
5
6 is lit
6
5
Pict. 2
Pict. 3
4 (Heating level +) fi ve times. All
9