Descargar Imprimir esta página

MSW SSM-2500 Manual De Instrucciones página 5

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 14
EN
e)
Clean the device regularly to prevent stubborn grime
from accumulating.
f)
The device is not a toy. Cleaning and maintenance may
not be carried out by children without supervision by
an adult person.
g)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
h)
Do not overload the device.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The product is intended to assist in the processing of
workpieces with a miter saw. The product is intended for
home use only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
NOTE: the picture shows the MSW-SSM-200 model, the
other models are similar. The miter saw is not part of the
set but only presented for illustrative purposes.
B
J
E
F
A
F
C
D
G H
J
C
O
C
O
O
A.
Main frame
B.
Miter saw (not included!)
C.
Leg
D.
Support bracket
E.
"T" support
F.
Saw locks
G.
1 / 4-20 x 1—3 / 4 hex bolt
H.
1 / 4-20 nut
8
I.
Saw assembly kit (screw + washer + nut, not visible in
the picture)
J.
5 / 16-18 point clamp knob
K.
5 / 16-18 x 2-1 / 2 clamping screw
L.
5 / 16-18 nut
M.
5/16 flat washer
N.
Lock washer
O.
Feet
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The ambient temperature must not exceed 45°C and the
relative humidity should not exceed 85%. Only use the
device in well-ventilated areas. Keep the device away from
any hot surfaces. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions.
ASSEMBLING THE APPLIANCE
MSW-SSM-2500
a)
Take out the main frame, put it upside down and
unfold the legs taking care that their locks click into
the holes. Put the main frame on its feet.
b)
Insert the support bracket into the frame holes and fix
it with the point clamp knob. Repeat on the other end
of the frame.
c)
Mount the "T" supports in the brackets and lock them
with the point clamp knob.
E
C
O
NOTE: The point clamp knobs are used to position the
support and brackets when the machine is used.
d)
On the frame, install the locks securing the saw. First
place them on the lever side. After mounting them,
lock them by moving the lever handle downwards
(see the picture opposite).
Rev. 19.02.2021
e)
To attach the miter saw to the frame, use the bolts
included in the set with washers and nuts (the bolts
should be inserted from the top).
f)
The clamping lock levers should be facing the front of
the saw (the blade).
NOTE: for miter saws with atypical mounting, e.g. with
only 3 mounting holes or 4 mounting points, where
the holes on the right or left side are not parallel to
each other, it is recommended to prepare a special
adapter (e.g. made of 20 mm plywood).
MSW-SSM-3000
A
Rev. 19.02.2021
EN
C
B
F
E
F E
C
D
F
B
D
F
F
MSW-SSM-200
1
6
2
3
4
See the picture in sec. 3.1
a)
Fix the legs (C) to the main frame (A) with bolts (G)
and nuts (H). Make sure the locking pin protrudes
outward and snaps into place in both open and closed
positions.
b)
Turn the frame upside down and open the legs by
pressing in the pins and unfolding the legs.
c)
Install the feet (O) on all four legs – see fig. 2 above.
Put the subframe on its feet.
F
5
7
8
9
9

Publicidad

loading

Este manual también es adecuado para:

Ssm-3000Ssm-200