Regular Maintenance; Preventive Maintenance - Domyos INTENSE RUN Manual De Instrucciones

REGULAR MAINTENANCE

PREVENTIVE MAINTENANCE

Inspect the motor and the conveyor belt after every 600 hours of use or 3600 km*
Change the running belt after every 500 hours of use or 3000 km*
Change the running deck after every 700 hours of use or 4200 km*
To find out how many hours the treadmill has been in use since it was first switched on, press
Then press 6 times until you see the screen below.
Find all our maintenance tips on the domyos.com site in the after-sales service section.
TROUBLESHOOTING
The treadmill will not turn on:
Check that the power cord is plugged into a wall socket in working condition (to check if the wall socket is working, plug in a lamp or other electrical device to check).
Check that the power cord is plugged into a wall socket that is properly grounded. If you need an extension lead, use only a 3-core, 2,5 mm² (14 gauge) cable that is no
longer than 1.5 m (5 ft).
Check that the power cord is fully inserted in the back of the treadmill.
After connecting the power cord, make sure that the key is inserted into the console.
Check the switch on the frame of the treadmill near the power cord, it must be in the «I» position.
The treadmill turns off during use:
Make sure the power cord is correctly plugged into the wall socket and the back of your treadmill.
Remove and reinsert the console safety key.
The running belt slows down when walked on:
If you need an extension lead, use only a 3-core, 1 mm2 cable that is no longer than 1.5 m. Do not use a power strip.
If the running belt is too tight, the performance of the treadmill may decrease and the running belt may become damaged.
Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn the running belt centring and tensioning screws anticlockwise a quarter turn. When the run-
ning belt is properly tightened, you should be able to lift each edge of the running belt 2 to 3 cm above the deck. Ensure the running belt remains centred. Then, plug in the
power cord, insert the safety key and run the treadmill for a few minutes.
The treadmill makes a noise:
Rubbing noise:
Check that the running belt is properly centred (the belt must not rub against the sides).
Check that the running belt is properly tightened (the belt must not slip).
Check, and if necessary, tighten all the external parts of the running belt.
Grinding noise:
The running belt is no longer centred:
Locate the colour indicators on the back of your treadmill.
If you see red, the belt needs to be re-centred. This helps protect the running belt and avoids unexpected shutdowns.
Run your treadmill at 4km/h (2.5 mph) and stand at the back of the machine.
24
Lubricating the running belt:
It is advisable to lubricate your treadmill in order to limit the amount of friction between the running belt and the
deck. No lubrication is necessary if traces of silicone are present on the inner side of the running belt or on the
deck (and the surface is damp and slightly greasy).
1. Turn off your treadmill and unplug it.
2. Lift the edges of the running belt and coat the inner surface with 5 to 10ml of silicone.*
3. Plug your treadmill in again.
4. Make the belt rotate at a speed of 4 km/h (2.5 mph), with no-one on it, for 10 to 20 seconds.
5. Your treadmill is ready for use!
*Please note that if you use too much silicone, you could harm the proper functioning of your treadmill (risk of
skidding).
The belt is offset to the left:
Turn the left adjustment screw clockwise a half turn.
The belt is offset to the right:
Turn the right adjustment screw clockwise a half turn. Leave your treadmill running
until the belt repositions itself (1-2 minutes) and repeat the operation if necessary.
However, be careful not to overtighten the belt.
The running belt stops while running
The running belt is a wearing part that becomes loose over time. Re-tighten it as
soon it begins to slip (sliding sensation, jerks in speed).
Turn the 2 adjustment screw clockwise a half turn. Repeat the operation if necessa-
ry, but be careful not to overtighten the belt. The belt is properly tightened if you can
lift the edges 2 to 3 cm on each side
+ + insert the safety key