Remote Control - REVELL FUNTIC Manual De Instrucciones

• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Rotors
1B Protective bar
1C Front LED

2 REMOTE CONTROL

2A Trim for rotation
2B Control for thrust and rotation, pressing
vertically activates headless mode
2C LED on/off
2D Power LED
2E Turbo switch
2F Flip button
2G Control for forwards/backwards and
sideways flight
16
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 1,9 Wh
Batteries: 3,7 V
rechargeable
LiPo battery (included)
Capacity: 500 mAh
Battery requirement for the
remote control:
Power supply:
DC 4,5 V
Batteries:
3 x 1.5 V "AA" (not included)
USB charger:
Power supply: DC 5V via USB port,
500 mA or higher
Rated output: 4,2 V / 500 mAh max.
1 MODEL
1D Battery compartment
1E ON/OFF switch
2H Trim for forwards/backwards
2I Trim for sideways
2J ON/OFF switch
2K Battery compartment cover
2L Opening lever for the battery
compartment
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Press the opening tab 3B Insert 3 x 1.5 V AA batteries
(2L) down and lift off the and pay attention to the
battery compartment cover polarity specifications, as
(2K) to open the battery indicated in the battery
compartment. compartment.
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 15 to 30 minutes before charg-
ing and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Open the battery compartment (1D), unplug the battery from the model (4A), and
switch off the remote control. Remove the battery from the model (4B). Plug the USB
charger into an open USB port (4C). The status LED on the charger begins to illuminate.
• Plug the white battery plug into the socket of the charger. Make sure that the polarity is
correct in the process (4D). The battery must be gently inserted into the charging
socket – DO NOT USE FORCE. If the battery is not correctly inserted into the charging
socket, the battery may become damaged and, under certain circumstances, cause
injury.
• The red LED on the USB charger goes out when the charging process starts.
• The charging process lasts approx. 90 minutes and must be continuously monitored.
The red LED on the charger lights up as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx. 90
minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. Open
the battery cover (1D), insert the battery into the battery compartment of the model, plug
the battery plug into the socket in the model, and close the battery compartment. Do not
use force and ensure tThen set the ON/OFF switch on the model (1E) to the „ON" position.
Before switching on the remote control, the control for thrust and rotation (2B) must
point down (5B). Press the ON/OFF switch (2J) on the remote control to switch it on.
After approx. 3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
3C Close the battery
compartment cover.
17