Maintenance / Service - Skil 1310 Manual Original

- check for a 90° angle between blade and table with a
square
- if necessary, adjust the 90° blade alignment as follows:
1. loosen three-legged knob U
2. adjust screw W with a blade wrench 10 (not
standard included)
3. re-check with square
4. reset the bevel indicator V to 0°
• Checking/adjusting of 45° blade alignment l
! disconnect the plug
- rotate the saw table to the 0° mitre position and lock in
place
- loosen three-legged knob U
- swing the saw head to the left
- check for a 45° angle between blade and table with a
mitre square
- check that bevel indicator V is on the 45° mark
- if necessary, adjust the 45° blade alignment as follows:
1. adjust screw X with a blade wrench 10 (not standard
included)
2. re-check with mitre square
• Checking/adjusting of 90° fence alignment z
! disconnect the plug
- rotate the saw table to the 0° mitre position and lock in
place
- lower the saw head and lock in place
- check for a 90° angle between blade and fence S with a
square (ensure the square contacts the saw blade body
and not its teeth) z )a
- if necessary, adjust the 90° fence alignment as follows:
1. loosen 2 hex screws T z b
2. adjust fence until blade and fence have full contact
with the square
3. tighten 2 hex screws T
4. reset the mitre indicator to 0° z c
APPLICATION ADVICE
• Special workpieces
- always support the free ends of a long workpiece x
- ensure that curved or round workpieces are especially
secured against slipping c
- at the cutting line no gap may exist between the
workpiece and the fence or saw table
- if necessary, fabricate an auxiliary fence; the holes in
the sliding fence shall be used to secure the auxiliary
fence v
! the auxiliary fence can only be used at 0° bevel
• For working with floor mouldings illustration b can be
used as reference
• Always face the good side of the workpiece down to
ensure minimum splintering
• Only use sharp saw blades of the correct type
- quality of cut improves by the number of teeth
- carbide tipped blades stay sharp up to 30 times longer
than ordinary blades

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially the
ventilation slots at the back-end of the motor housing)
• Develop a regular check to make sure the lower guard is
working properly. Clean the lower guard of any sawdust
build up with a damp cloth.
! disconnect the plug before cleaning
- lift the lower guard to the fully open position and
release it; if it does not immediately and fully close it
should be checked by an after-sales service centre for
SKIL power tools
• Clean saw blade immediately after use (especially from
resin and glue)
! the saw blade becomes very hot during use; do
not touch it before it has cooled down
• Clean the laser light AC with a soft brush after each use
to keep a good visibility of the laser line (make sure that
you do not change the setting of the laser)
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
NOISE
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 100.0 dB(A) and the sound
power level 109.5 dB(A) (uncertainty K = 3 dB)
• The noise emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as a
preliminary assessment of exposure to noise when using
the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
b
Scie à onglets radiale
INTRODUCTION
• Cet outil est une machine fixe, conçue pour effectuer
dans le bois des coupes droites longitudinales et
transversales ainsi que des angles d'onglet (il est
possible de réaliser des angles d'onglet horizontaux de
-47° à +47° et des angles de biseau verticaux de 0° to
45°)
20
1310