Ideal PowerPlug 102 Instrucciones De Instalación

PowerPlug Luminaire Disconnect -
®
Model 102
Installation Instructions:
To be sold only with installation instructions.
WARNING: This is a current rated device. Use in applications involving
amperage beyond its rating can be dangerous and cause electrical fires. See
note on this page for allowable current and voltage levels and do not exceed
those levels.
Instructions:
Conductor installation:
1. Wiring must comply with all
applicable electrical codes.
2. Turn off power before removing or
installing disconnect.
3. Strip wires to 3/8 inch (9,5 mm).
4. Grip black ballast wire firmly and push conductor
into white cap port marked with black circle.
5. Grip white ballast wire firmly and push conductor
into same side of connector in port marked with
white circle.
6. Grip black supply wire firmly and push conductor into port opposite black ballast wire.
7. Grip white supply wire firmly and push conductor into remaining port.
8. Use only one conductor per port and assure that no copper is exposed on any of the wires
inserted.
9. See disconnect de-mate/mate installation instructions below when replacing ballasts.
10. The wire insertion side of this product is listed for ONE TIME USE ONLY. DO NOT
REMOVE AND REPLACE WIRES.
PowerPlug Luminaire Disconnect -
®
Model 102
Installation Instructions:
To be sold only with installation instructions.
WARNING: This is a current rated device. Use in applications involving
amperage beyond its rating can be dangerous and cause electrical fires. See
note on this page for allowable current and voltage levels and do not exceed
those levels.
Instructions:
Conductor installation:
1. Wiring must comply with all
applicable electrical codes.
2. Turn off power before removing or
installing disconnect.
3. Strip wires to 3/8 inch (9,5 mm).
4. Grip black ballast wire firmly and push conductor
into white cap port marked with black circle.
5. Grip white ballast wire firmly and push conductor
into same side of connector in port marked with
white circle.
6. Grip black supply wire firmly and push conductor into port opposite black ballast wire.
7. Grip white supply wire firmly and push conductor into remaining port.
8. Use only one conductor per port and assure that no copper is exposed on any of the wires
inserted.
9. See disconnect de-mate/mate installation instructions below when replacing ballasts.
10. The wire insertion side of this product is listed for ONE TIME USE ONLY. DO NOT
REMOVE AND REPLACE WIRES.
3/8" Strip
Length Indicator
3/8" Strip
Length Indicator
DANGER
NEVER remove wires from product as contact with electricity can cause serious injury or death.
Shut off power at the circuit breaker or remove fuse when installing this product.
SAFETY NOTICE
Improperly installed electrical wiring can be dangerous and cause electrical fires. This product
must be used in accordance with the current rating and wire sizes listed. Consult local building
code before doing any electrical work.
COPPER TO COPPER ONLY. Do not use on Aluminum. Temperature rating: 105 C (221F)
maximum. Flame Rated UL94V-0.
Voltage Rating: 600 Volts Maximum Current Rating: 6 Amps Maximum
Rated for a limited number of current-interrupting operations.
Wire Range:
Solid: 12-18 AWG
Stranded: 12-14 AWG (19 Strand or less)
Stranded Tin Bonded: 12-14 AWG (19 Strand or less)
16 AWG (26 Strand or less)
18 AWG (16 Strand or less)
Disconnect de-mate / mate installation
1. To de-mate, grasp disconnect at each end and pull
apart to separate the disconnect halves. Do NOT pull
on wires.
2. To mate the disconnect, grasp each disconnect half,
align halves, and push together.
Insert black ballast
wire into port marked
with a black circle
Line Side Wires
12 - 18 AWG
DANGER
NEVER remove wires from product as contact with electricity can cause serious injury or death.
Shut off power at the circuit breaker or remove fuse when installing this product.
SAFETY NOTICE
Improperly installed electrical wiring can be dangerous and cause electrical fires. This product
must be used in accordance with the current rating and wire sizes listed. Consult local building
code before doing any electrical work.
COPPER TO COPPER ONLY. Do not use on Aluminum. Temperature rating: 105 C (221F)
maximum. Flame Rated UL94V-0.
Voltage Rating: 600 Volts Maximum Current Rating: 6 Amps Maximum
Rated for a limited number of current-interrupting operations.
Wire Range:
Solid: 12-18 AWG
Stranded: 12-14 AWG (19 Strand or less)
Stranded Tin Bonded: 12-14 AWG (19 Strand or less)
16 AWG (26 Strand or less)
18 AWG (16 Strand or less)
Disconnect de-mate / mate installation
1. To de-mate, grasp disconnect at each end and pull
apart to separate the disconnect halves. Do NOT pull
on wires.
2. To mate the disconnect, grasp each disconnect half,
align halves, and push together.
Insert black ballast
wire into port marked
with a black circle
Line Side Wires
12 - 18 AWG
Load Side Ballast Wires
18 AWG (typ.)
IDEAL INDUSTRIES, INC.
1375 Park Avenue
Sycamore, IL 60178, U.S.A.
800-435-0705 Customer Assistance
www.idealind.com
ND 6184-9
TITLE:
SCALE:
IDEAL INDUSTRIES, INC.
DATE
3-3-08
SYCAMORE, ILLINOIS, U.S.A.
Load Side Ballast Wires
18 AWG (typ.)
IDEAL INDUSTRIES, INC.
1375 Park Avenue
Sycamore, IL 60178, U.S.A.
800-435-0705 Customer Assistance
www.idealind.com
ND 6184-9
MODEL
4:1