Noise/Vibration Information; Declaration Of Conformity - Berner BROS-125/150 AVE Manual Original

OBJ_BUCH-1801-002.book Page 14 Monday, November 16, 2015 8:42 AM

Noise/Vibration Information

Sound emission values determined according to EN 60745-2-4.
Typically the A-weighted noise levels of the product are: Sound pressure level 82 dB(A); Sound power lev-
el 93 dB(A). Uncertainty K =1.5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 60745-2-4:
h
Application
Measurement according to EN 60745 for sanders (using sanding sheet with grain size 180):
Sanding with maximum removal rate
Intermediate varnish sanding
Fine sanding softwood
Fine sanding hardwood
Fine sanding veneer
Sanding old paint and varnish
Sanding metal
Sanding filler
Sanding wood and veneer edges
Intermediate varnish sanding on edges
Sanding thermoplastics
Measurement according to EN 60745 for polishers (using lambskin polishing bonnet):
Polishing
The vibration level given in this information sheet
has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with different
accessories or insertion tools or is poorly main-
tained, the vibration emission may differ. This may
significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not ac-
tually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amend-
ments and complies with the following standards:
EN 60745-1, EN 60745-2-4, EN 50581.
14 | English
Oscillation Application Force
Rate [N]
6 50
5 – 6 10 – 20
5 – 6 0 – 10
5 – 6 10 – 20
5 – 6 10 – 20
5 – 6 30 – 40
5 – 6 30 – 40
5 – 6 20 – 30
3 – 4 0 – 10
3 – 4 0 – 10
1 – 2 0 – 10
1 0 – 10
Technical file (2006/42/EC) at:
Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
Armin Hess
Chairman of the Management Board
15.11.2015, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
Assembly
 Before any work on the machine itself, pull the
mains plug.
Replacing the Sanding Sheet
(see figure A)
To remove the sanding sheet 10, lift it from the side
and pull it off of the sanding plate 8.
When attaching a new sanding sheet, remove any
dust or debris from the sanding plate 8, e. g., with
a brush.
a K
h
2 2
[m/s ] [m/s ]
2.5 1.5
2.5 1.5
2.5 1.5
2.5 1.5
2.5 1.5
2.5 1.5
2.5 1.5
2.5 1.5
5.5 1.5
5.5 1.5
7.5 1.5
3.5 2.5
1 609 92A 1SE • 16.11.15