Kit Contents; Important Warnings - OKBABY Onda Manual De Instrucciones

HOW TO CORRECTLY INSTALL THE "ONDA / ONDA EVOLUTION" TUB FOR BABIES
EN
OVER AN ADULT-SIZED BATHTUB. REF. 823/808/809
IMPORTANT/NOTE: Read these instructions carefully before use and keep them for future reference.
DANGER! DO NOT LEAVE THE CHILD UNATTENDED TO AVOID DROWNING
AGES: approximately 0 to 12 months.
REQUISITES FOR THE ADULT-SIZED BATH:
The following "Onda / Onda Evolution" bath support kit, adapts to almost all standard adult-sized baths
on sale, excluding corner ones, that have the two long parallel sides and an internal distance of between
a minimum of 53 cm and a maximum of 75 cm. The edge of the adult-sized bath must also have a flat
supporting surface of 2 cm. minimum. (Fig. A).

KIT CONTENTS:

• three bar slideways ;
• eight fixing screws;
• pair of support bars (each bar is made up of two rotating halves and two rubber stops at the ends).
DIRECTIONS:
1. Fix the three bar slideways in the appropriate housings on the bottom of the "Onda / Onda Evolution" tub,
using the eight fixing screws supplied (Fig. B).
IMPORTANT/NOTE: Tighten the screws in all eight housings in the tub.
ATTENTION: once fixed, the three guides should no longer be removed as the screws may lose their hold.
2. Regulate the length of the support bars as follows (Fig. C):
• Release the three cogs (1) from their housing rotating the two halves of the bar to open.
• Lengthen or shorten the bar so that the two horizontal supporting rubber parts rest on the edges of the
tub whilst the two vertical supporting parts are in contact with the internal wall of the adult bath. This way
the bar is positioned tightly, without any slack, transversally to the adult bath (Fig. D).
• Once the right measurement has been established, close by rotating the two halves of the bar, inserting the
teeth in their housings until the safety clasp triggers (fig. C).
IMPORTANT/NOTE: After identifying the right measurement, we advise making a mark with a felt-tipped
pen on the bars so that each time you use the bars you do not have to repeat the operation of finding the
correct measurement.
IMPORTANT/NOTE: Make sure the safety clasp is correctly closed.
3. Insert the two sliding bars into the previously fixed slideways (Fig. A). At this point, position the
"Onda / Onda Evolution" tub on the adult-sized bath.
IMPORTANT/NOTE: The baby tub can move along the slideways on the bars to be positioned as you require.
IMPORTANT/NOTE: Each optional or spare part must only be ordered from the manufacturer or dealer.
IMPORTANT/NOTE: Do not use the tub or bars if damaged.

IMPORTANT WARNINGS:

• DANGER! Check the stability of the bars before each use: both the bars must be fixed between
the edges of the adult-sized bath, there must not be the possibility of transversal movement
between the bars and the edges. Failure to observe this point may cause the bath to tip over with
consequent injury for the baby.
• WARNING: The bars have been designed to support the weight of the tub containing the water
and the child. Do not lean against it or add any other weights.
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. WARNING - Not a safety device. WARNING -
DROWNING HAZARD. Children have drowned while bathing. Children have drowned while using bathing aids products.
Children can drown in as little as 2 cm of water in a very short time. Always remain in contact with your child during
bathing. Never leave your baby unattended in the bath, even for a few moments. If you need to leave the room, take the
baby with you. DO NOT allow other children (even older) to substitute for an adult. WARNING. Babies and young children
are at risk of drowning when being bathed. Never use this product on an elevated surface not intended for this product.
The only elevated surfaces approved are the bath stands mod. 845, 893, 897 and 901. To avoid scalding by hot water,
position the product in such a way to prevent your child from reaching the source of water. Check the temperature of
the water surrounding the product prior to placing the child into the product. The typical water temperature for bathing
a child is between 35 °C and 38 °C. The symbol "MAX
water to be used. Check the stability of the product before use. Do not use the product if any components are broken or
missing. Do not use replacement parts other than those approved by the manufacturer or distributor. Rinse the product
and air dry before putting away. Do not use solvents or abrasives. It is recommended to store the product in a dry place.
Only for bath cradles mod. 794, 818 and 910: stop using the product when your child can sit unaided. Always ensure the
suction cups are well adhered to the bath tub. Do not use this product on a bath tub with an uneven surface. Only for
bath seats mod. 799 and 871: use this product only when your child is able to sit unaided. Stop using this product when
your child tries to stand up by itself. Ensure the level of water is not higher than your child's navel. Always ensure the
suction cups are well adhered to the bath tub. Do not use this product on a bath tub with an uneven surface.
Max 15 Kg. For home use only.
" on the product is used to indicate the maximum level of
5