Ec Declaration Of Conformity; General Power Tool Safety Warnings - Makita DHR280 Manual De Instrucciones

Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745-2-6:
Model DHR280
Work mode: hammer drilling into concrete
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: hammer drilling into concrete with DX08
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: chiselling function with side grip
Vibration emission (a
h, Cheq
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a ) : 2.5 m/s
h,D
Uncertainty (K) : 1.5 m/s
Model DHR281
Work mode: hammer drilling into concrete
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: hammer drilling into concrete with DX09
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: chiselling function with side grip
Vibration emission (a
h, Cheq
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a ) : 2.5 m/s
h,D
Uncertainty (K) : 1.5 m/s
Model DHR282
Work mode: hammer drilling into concrete
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: hammer drilling into concrete with DX08
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: chiselling function with side grip
Vibration emission (a
h, Cheq
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a ) : 2.5 m/s
h,D
Uncertainty (K) : 1.5 m/s
Model DHR283
Work mode: hammer drilling into concrete
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: hammer drilling into concrete with DX09
Vibration emission (a
h, HD
Uncertainty (K) : 1.5 m/s
Work mode: chiselling function with side grip
Vibration emission (a
h, Cheq
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a ) : 2.5 m/s
h,D
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
2
): 9.0 m/s
2
2
): 8.0 m/s
2
2
): 8.5 m/s
2
2
2
2
): 9.5 m/s
2
2
): 8.0 m/s
2
2
): 9.0 m/s
2
2
2
2
): 9.0 m/s
2
2
): 8.0 m/s
2
2
): 8.0 m/s
2
2
2
2
): 9.5 m/s
2
2
): 8.0 m/s
2
2
): 8.5 m/s
2
2
2
WARNING:
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS

General power tool safety warnings

WARNING:
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
CORDLESS ROTARY HAMMER
SAFETY WARNINGS
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
3. Hold power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
4. Wear a hard hat (safety helmet), safety glasses and/
or face shield. Ordinary eye or sun glasses are NOT
safety glasses. It is also highly recommended that
you wear a dust mask and thickly padded gloves.
Be sure the bit is secured in place before operation.
5.
6. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
7. In cold weather or when the tool has not been
used for a long time, let the tool warm up for
a while by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
11 ENGLISH
The vibration emission during actual
Be sure to identify safety measures
Read all safety warnings, instruc-