Publicidad
garden
and
gardening
SAFETY ADVICE
Rion
is
not responsible for the
misuse
of tools
or parts.
It
is
of utmost importance to
assemble
all
of
the parts according to the directions.
Please
follow them
closely and
do
not
skip any step.
We
strongly recommend
using
work
gloves
during
assembly.
If using
a
step ladder or
power tools
ensure
that
you
follow the manufacturer's
safety advice.
If local
building
codes
require permits or licenses make
sure
that they
are
acquired before beginning.
Your Greenhouse
should
be secure by
anchored to the prepared
foundation
using the recommended hardware.
Do
not attempt to
assemble
the greenhouse
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not
lean
against or push the greenhouse during construction.
Do
not attempt to
assemble this greenhouse
if
you
are
tired,
have
taken drugs or alcohol or if you
are
prone to
dizzy spell.
Hot items
such
as
recently
used grills,
blowtorches
etc.
must not
be
stored
in
the greenhouse.
Ensure
there
are
no
hidden pipes or cables
in
the ground before inserting the
pegs.
When
your Greenhouse
is
fully
assembled examine it for sharp edges and
trim with
a
razor knife if necessary.
If
you live
in
a
hot climate, where outside temperatures
exceed
46°
C
(115°
F)
in
the
sun
or
36°
C
(99°
F)
in
the
shade,
this may
cause
the temperature inside the greenhouse to
exceed
55°
C
(131°
F).
Such
conditions
may harm
your plants and will damage the greenhouse by warping structural profiles.
In
order to prevent damage:
Ensure
good ventilation during hot
days.
Make sure
that the temperature
inside the green house never exceeds
55°
C
(131°
F)
by
providing
a
shading
screen, such
as
the
Shade Net (available
as
an
accessories
option).
Note:
RION
is
not responsible for
any
damage due to high temperatures.
* Always close
roof vent
in
high winds.
REQUIRED TOOLS
GT1
-
Special
tool
to connect pins through lined up
holes. Pin Tool
fix and lock profiles in place
To
assemble this
product you will
need the
following
tools
(these
items
not
suppl
ed)
411
BEFORE ASSEMBLY
Rion
is
not responsible for the
misuse
of tools
or parts.
Selecting
a
site
-
the greenhouse must
be,
positioned
and fixed on
a
flat
level surface.
Sort the parts and check according to the contents parts list. Do
not begin assembly if
any parts
are
missing.
If
you prepare
a
concrete foundation do not excavate and pour concrete
in
frozen
ground.
We
recommend that you place your Greenhouse
in
a
spot where it will receive direct sunlight
and
will
be
protected from the wind
as
much
as
possible. The
door should not
face
prevailing winds.
DURING ASSEMBLY
Steps 2-5: Arrange
all
2D
connectors
with
the stamped word
OUT
facing the outside
of
the greenhouse.
Step 6:
Make sure
that the
frame
is
perfectly straightened
by measuring the diagonals and
verifying that they
are
the
same.
Make sure
that the
frame
is
level and
anchor
it
with
screw
/
screw
+
dibble
/
spike (not included) according to the
selected surface.
Step 12:
Walls
assembly must
be
made
gradually
(1.panel 2.rofile 3.connector) according
to describe method
in
step #11.
Attention:
DWhen
encountering the information
icon, please refer to the
relevant assembly step for additional comments and
assistance.
This icon
indicates
that
the installer should
be
inside the product.
Publicidad
