Logiche Di Funzionamento - Seav BeWeather Serie Manual De Instrucciones

Funzionamento con radiocomando 1 Tasto :
Utilizzando il radiocomando con un solo tasto, si ottiene il se-
guente funzionamento: il primo impulso comanda la Salita fino
allo scadere del tempo motore. Il secondo impulso comanda la
Discesa del serramento; se un impulso perviene prima dello
Operation using a 3-button radio control (BeFree x3 - X6):
scadere del tempo motore, la centrale effettua l'arresto del ser-
When using the BeFree x3 - x6 radio control, you will obtain the same operation as previ-
ously described for the BeFree x1 version; in addition, by using the keys (-) and (+) at the
ramento, un ulteriore impulso effettua la ripresa del moto nel
sides of the radio control it is possible to select the UP – STOP – DOWN controls for 3
senso opposto di marcia.
different types of use (BeFree x3) or for 6 different types of use (BeFree x6). In addition,
by using the keys (-) and (+) at the sides of the radio control it is possible to enable and
Funzionamento con radiocomando 2 Tasti :
disable the sun sensor (the selection is confirmed by a quick UP / Down movement of
Utilizzando il radiocomando con 2 tasti, si ottiene il seguente
the motor).
funzionamento, il primo tasto ( "Up" associato al senso di
INVERSION OF THE ROTATION MOTOR
salita ) comanda la Salita fino allo scadere del tempo motore ed
If you notice that when pressing the UP key on the radio-control the control unit causes
il secondo tasto ( "Down" associato al senso Discesa ) coman-
the shutter to move upwards instead of downwards, simply repeat the programming
da la Discesa del serramento. Nel caso in cui durante la Salita
procedure pressing the DOWN key instead of the UP key, or invert the motor's Upward
movement wire and the Downward movement wire.
viene inviato nuovamente un comando Up, la centrale continua
il moto di Salita, mentre se viene inviato un comando Down, la
GROUP OR GENERAL CENTRALISATION
centrale effettua l'arresto del moto.
It is also possible to enter two identical codes ( buttons ) from one radio control onto
all the control units or a group of them which are situated at a maximum distance of 20
La stessa procedura è valida nella fase di Discesa.
metres from the point of command, in order to obtain general or partial motion of more
than one automation.
Funzionamento con radiocomando 3 tasti (BeFree x1):
ANEMOMETER OPERATION
The electronic control unit will cause the sun shade to move upwards every time the wind
exceeds the selected threshold.
SUN SENSOR OPERATION
The electronic control unit controls the downward movement of the sun shade after 5
minutes during which the brightness is greater than the threshold selected using the VR1
trimmer and displayed when the SUN LED lights up; it also controls the upward movement
of the shade after 5 minutes during which the brightness is below the selected threshold.
Sun sensitivity adjustment ( 5 ¸ 40 Klux )
The control unit allows you to adjust the sensitivity of the Sun Sensor using the VR1
trimmer. When the SUN LED lights up on the control unit, this indicates that the intensity
of the sun exceeds the selected threshold; this enables you to use the current light condi-
tions as a reference when setting the desired value.
RAIN SENSOR OPERATION
The electronic control unit will cause the sun shade to move upwards as soon as the
sensitive part of the rain sensor gets wet with water as displayed when the RAIN LED
lights up.
F S
UNZIONAMENTO DEL
La centrale elettronica comanderà la salita della tenda non ap-
pena la parte sensibile del sensore pioggia viene bagnata dal-
l'acqua, segnalata tramite l'accensione del LED RAIN.
OPERATION PRINCIPLES
L F
OGICHE DI UNZIONAMENTO
SW1 SW1
SW1 SW1
Step-by-step P/P + Aut Sensors
Passo Passo P/P+Sensori Aut Uomo presente
1) Step-by-step (Dip 1 and 2 OFF)
The electronic control unit has a cyclic "Step-by-Step" logic, whose operation depends on the
1) Passo - Passo (Dip 1 e 2 OFF)
type of radio control associated with it (see operation with radio control with 1-2-3 buttons).
2) Step-by-step + Aut. Sensors (Dip 1 ON and Dip 2 OFF)
The electronic control unit allows the "Step-by-Step" operation as described above, with the
addition of the automatic control of the Wind and Rain sensors. After the activation of one of
1
the two sensors, once the disturbance is over, the electronic control unit controls the downward
movement of the sun shade after 5 minutes.
3) Manually-controlled (Dip 1 OFF and Dip 2 ON)
Using the radio control the "User present" operating mode can be obtained, i.e. the control must
be constantly enabled so that the blind or shutter can be moved as necessary. The movement
stops when the control is released.
4) Sensor Test (Dip 1 and 2 ON)
The electronic control unit allows to check the sensor operation and the correct rotation
direction upon installation; we advise that you place the shade in intermediate position in
order to verify the confirmation movements during the tests.
Warning: after you have tested the sensors, restore the Dip 1 and 2 in the desired opera-
tion mode.
Anemometer:
manually turn the Anemometer blades; at the same time, the control unit will cause an upward
movement lasting 5 seconds.
Sun sensor :
turn the VR1 trimmer as far as possible in a clockwise direction (in the + position); at the same
13
P
ENSORE IOGGIA
SW1 SW1
SW1 SW1
User Present Sensor Test
Test Sensori
Rev. 3.0 05/09/2016