Seav BeWeather Serie Manual De Instrucciones página 14

time, the control unit will cause the SUN LED to light up and there will be a downward movement
lasting 5 seconds. Turn the VR1 trimmer in an anticlockwise direction (in the – position); at the
same time, the control unit will cause the SUN LED to switch off and there will be an upward
movement lasting 5 seconds.
Rain sensor:
get the sensitive part of the Rain Sensor wet; at the same time, the control unit will cause the
RAIN LED to light up and there will be an upward movement lasting 5 seconds. When you have
completed the test, make sure you have dried the sensitive part of the rain sensor before using
the control unit in the normal operation mode.
PROGRAMMING BUTTONS AND INDICATOR LEDS
SEL button: selects the type of function to store; selection is indicated by the LED flash-
ing. The desired function can be selected by pressing the button repeatedly. The selected
function remains active for 15 seconds (flashing LED) following which the control unit
returns to its original status.
SET button: programmes the function that has been selected using the SEL. Key.
Indicator LEDs:
LED on: option stored.
LED off: option not stored.
Flashing LED: option selected.
———————————— MAIN MENU
Reference Led LED Off
1) CODE No code
2) T. MOT. Motor time 2 minutes
3) WIND SPEED Wind safety 25 km/h
4) SUN SENSOR Sun sensor = OFF
5) RAIN SENSOR Rain sensor = OFF
6) SUN Sun Presence = No
7) RAIN SENSOR Rain Presence = No
8) R. HEAT R. Heat = No
1) CODE (Radio control programming)
Programming using a 1- or 2-button radio control:
To programme the transmission codes in the radio control, proceed as follows: press the
SEL key; the CODE LED begins to flash. Send the first preselected code using the relevant
radio control at the same time; when the CODE LED begins to flash rapidly send the second
code to be stored. The CODE LED will remain lit and the programming will be complete.
If the second code is not sent within 10 seconds the control unit exits the programming
stage, selecting the function using a single button on the radio control. If you have stored 10
codes and you repeat the programming operation, all the indicator LEDs will start flashing
extremely rapidly to indicate that no more codes can be stored.
Programming using a 3 button radio control from the "BeFree" series.
The control unit allows you to store the whole "BeFree" radio-control by programming only
the UP button.
To programme the "BeFree" radio-control codes, follow this procedure: press the SEL key; the
CODE LED begins to flash. Press the UP key of the desired radio control at the same time; at
that moment, the CODE LED will remain lit and programming will be complete. If all of the
possible 10 radio control codes have been stored and you repeat the programming operation,
all indicator LEDs will start flashing very rapidly to indicate that no new codes can be stored.
Deleting the codes
To delete all transmission codes stored in the memory, proceed as follows: press the SEL
button; the CODE LED starts flashing. Then press the SET button; the CODE LED switches
off and the procedure is complete.
2) LED T. MOT.
( Motor Timer Programming )
The control unit comes with a motor power supply time of two minutes (T. MOT. LED OFF).
—————————————
The motor time must be programmed when the shutter is down and in the following way:
LED On
Press the SEL key until the T. MOT LED key flashes, then hold down the SET key; the shutter
will begin to move upwards. Once the desired position has been reached, release the SET
TX Pgm code
key – at this very moment, the motor time will be stored and the T. MOT LED will remain lit.
Pgm motor time
If you are using an automation which has a stop limit, we recommend that you set a time which
Pgm. Wind safety
exceeds the stop limit of the shutter by a few seconds.
Sun sensor = ON
If you want unlimited motor time, perform the same programming procedure, holding down
Rain sensor = ON
the SET key for less than two seconds; the T. MOT LED will remain lit and the unlimited time
Sun Presence = Yes
function will be set. The operation may be repeated if a mistake is made during programming.
Rain Presence = Yes
R. Heat = Yes
3) WIND ( Wind Safety Threshold Programming )
Displaying the programmed wind threshold
The wind safety threshold may be displayed in the following way: use the SEL key to navi-
gate to the WIND LED position; the LED will double-flash the same number of times as the
stored wind safety threshold (each WIND LED double-flash corresponds to an increase of 5
km/h), (for example: 5 WIND LED flashes = 25 km/h).
14