Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
FRAME RAIL
FLAT WASHER
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51094F
Wrenches: 3/4"
Drill Bits: NONE`
j
Qty. (6)
CARRIAGE BOLT 1/2-13 X 2.00 GR 5
k
Qty. (8)
FLAT WASHER 1/2
l
Qty. (6)
LOCK WASHER 1/2
IF PRESENT, LOWER CARBON CANISTER FROM DRIVER'S SIDE FRAME RAIL.
1.
2.
INSTALL FORWARD AND REARWARD CARRIAGE BOLTS AND BLOCK IN FRAME RAILS AS SHOWN.
3.
RAISE HITCH INTO POSITION AND HAND TIGHTEN FORWARD AND REARWARD FASTENERS TO BOTH RAILS AS
SHOWN.
4.
INSTALL CENTER CARRIAGE BOLT AND BLOCK IN FRAME PLACING FLAT WASHER BETWEEN RAIL AND HITCH AS
SHOWN. (DO NOT OVERLAP BLOCKS)
REATTACH CARBON CANISTER IF PRESENT – CARBON CANISTER MUST NOT CONTACT BOLT HEAD, IF IT DOES,
5.
LOOSEN CANISTER FASTENERS AND REPOSITION TO ENSURE CLEARANCE WITH BOLT HEADS.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2012 Cequent Towing Products
Installation Instructions
FORD ECONOLINE VAN
E-150, E-250 & E-350
STANDARD
BUMPER
STEP BUMPER
Tighten all 1/2 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
m
Qty. (6)
HEX NUT 1/2-13
n
Qty. (6)
BLOCK 1/4 x 1.500 x 2
51094N
Part Numbers:
51094
97094
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
8,000 (3632 Kg)
800 (363 Kg)
6,000 (2724 Kg)
600 (272 Kg)
2-1-12
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 51094
Resumen de contenidos para Cequent Towing Products 51094
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008, 2012 Cequent Towing Products Sheet 1 of 3 51094N 2-1-12 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2008, 2012 Cequent Towing Products Feuille 2 de 3 51094N 2-1-12 Rév.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. 2008, 2012 Cequent Towing Products Hoja 3 de 3 51094N 2-1-12 Rev.