EGO ST1500E-F Traducción De Las Instrucciones Originales página 9

◾
Always ensure that the ventilation openings are kept
clear of debris.
MAINTENACE AND STORAGE
◾
Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended
replacement parts and accessories.
◾
Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid Dangerous Environments – Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in a
location where the temperature is greater than 5° C
and less than 40° C. Do not store it outside or in vehicles.
◾
If you are approached, stop the motor and cutting unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust
(only using with 3-teeth blade).
◾
A coasting blade/line can cause injury while it
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1500E-F
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Use only with EGO's battery packs and chargers listed
below:
BATTERY
BA1120E, BA1400, BA2240E, BA2800,
BA3360, BA4200, BA1400T, BA2800T,
BA4200T,BA5600T
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
◾
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan this tool to someone else, also loan these
instructions to them to prevent misuse of the product
and possible injury.
◾
Always wear substantial footwear and long trousers
while operating the machine.
◾
Always be sure of the footing on slopes and to walk,
never run.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Voltage
No-load Speed
Cutting Mechanism
Cutting Line Type
Cutting Width
Recommended Operating Temperature 0°C-40°C
Recommended Storage Temperature -20°C-70°C
Weight (without battery pack)
EN
CHARGER
CH2100E,
CH5500E
56 V
4000-5800 /min
Bump Head
2.4mm nylon
twist line
38 cm
3.22 kg
9