Publicidad
Idiomas disponibles
Idiomas disponibles
•
Low speed (1) (lever forwards) for screwdriver action
and drilling ceramics and for starting to drill brick without a
piercer.
•
High speed (2) (lever backwards) for drilling brick (in
hammer mode), for drilling wood and derivatives, plastics
and metals.
The speed can be adjusted while the machine is running.
However, this should not be done at full load. If, when the
machine is stopped, the selector C cannot be set in its final
position, push the on/off E switch briefly.
4. Attachment of bits in the keyless drill chuck (Fig. 1)
1.
Open the drill chuck A and insert the drill bit or screwdriver
bit (in clamp H).
2.
To block the bit or screwdriver tip, turn the drill chuck in
a clockwise direction, looking at the machine from the front.
5. Torque adjustment (Fig. 1)
•
For use as a screwdriver, the drill-screwdriver is equipped
with an adjustable clutch, operated by the torque adjustment
control B which has 21 settings. Once it has been correctly
adjusted, the friction clutch is released when the preselected
torque setting is reached, to avoid the screw penetrating too
far or damage to the machine. Adjustment depends on the
type and size of the screw used. It is advisable to always
begin in the lowest setting (1) and increase gradually until the
desired result is obtained.
•
For use as a drill, set the torque adjustment control B to
the drill setting. The clutch is designed not to work in the drill
mode.
6. Hammer control (Fig. 1)
•
Hammer drill
Turn the torque adjustment screw B until the hammer figure
coincides with reference arrow.
To drill brick and similar materials, adjust the machine to
hammer drill mode. The bit hammers the material while it
turns.
When using the machine continually in hammer mode, it may
become hot. If this happens, leave it to cool. If the motor
blocks, unplug the machine immediately.
WARNING! When working in hammer mode, ensure the
machine turns in a clockwise direction!
•
Drilling without hammer
Turn the torque adjustment screw B until the drill bit figure
coincides with reference arrow S.
•
Screwdriver action
Adjust the torque adjustment screw B to the appropri-ate
position from 1 to 21 as described in the section covering
tightening torque adjustment.
CHARGING THE BATTERY (Fig. 2)
To remove the battery F from the machine, press both side
buttons, G, situated on the handle, at the same time.
To charge the battery with a quick 60 minute charger, proceed
as follows:
1.
Place the battery charger I on a flat surface and plug the
charger into the mains.
2.
Fit the battery F upside down into the charger. Ensure
that the battery tab is aligned with the inner slot on the
charger. Check that the terminals + and – of the battery and
the charger coincide. After putting the battery in the charger,
you will observe that the red color led J will flash as an
indicator that the battery is charging.
Note: If the flashing frequency of the red color led J is
very fast, or is not constant, it is an indicator that the battery
is in poor condition and should be replaced.
3.
Once the battery charge is completed, the red color led
J of the charger I will remain permanently lit. The battery has
been charged 100% and is ready for use.
.
Once the charge is completed and the red color led J is
lit up, the charger will maintain and balance the charge level
in the different battery cells so it is always ready and available
for use.
Respect the charge time indicated in the table.
Warning! Before charging a battery that has recently been in
use or exposed to direct sunlight or heat, leave it to cool. This
will enable it to be fully recharged.
DISCHARGE OF THE BATTERY
Once the battery is fully charged, the drill may be used again.
Try not to discharge the battery completely.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
Remove the battery before carrying out any operation on the
machine.
-
Clean the machine very carefully after each use. The air
vents should always be kept clear.
-
Store in a dry place, away from cold .
-
Use only Felisatti accessories and spares. These should
be fitted in a Felisatti technical service centre (See Warranty/
Technical Service Centre address leaflet).
-
Brush replacement: The brushes disconnect auto-
matically and should be replaced after 80 - 100 hours use
or when they are less than 3 mm long. Have them replaced
by an Official Service Centre. We recommend that at every
second change of brushes, you take the machine to one of
our Official Service Centres for general cleaning and oiling.
WARRANTY
See general warranty conditions printed on the attached
sheet.
5
Publicidad
