ELICA Aplomb WH/A/90 Montaje Y Modo De Empleo página 20

Timer (T4)
The timer can be activated when the first, second or third speed is
active. When the function is activated, both the LED of the Timer
(T4) and that of the previously selected speed (T1/T2/T3) turn on
with a fixed light.
The duration of the timer depends on the selected speed:
First speed T1 = duration 20'
Second speed T2 = duration 15'.
Third speed T3 = duration 10'.
When a speed is timed, the timer can be deactivated by pressing
T4, or one of the other two inactive speeds. To turn the hood off,
press the speed again to which the timer had previously been
linked.
NOTE: model A only
The timer cannot be activated when the booster is active. When
the time expires, the hood turns off. When a speed is timed, it is
possible to switch to other speeds by pressing the desired speed
button, this operation will turn the timer off.
Light (T5)
The light can be activated at any time by pressing key T5. When
the function is activated, the LED turns on with a fixed light.
Filter setting
Activation or deactivation of the filter indicators is only possible with
the hood off.
To access the configuration menu, hold pressed T2+T3, once
inside the menu T1 will start to flash.
The default setting is:
 grease filter indicator (T2) on, therefore active;
 odour filter indicator (T3) off, therefore not activated.
T2 activates/deactivates the grease filter indicator. T3
activates/deactivates the odour filter indicator. To exit the menu,
hold pressed T1 or wait 10''
Filter reset
The hood signals the need for filter maintenance at regular
intervals:
 grease filter every 40 hours;
 odour filter every 160 hours.
In this case, with the hood off, when the user touches any button
the interface signals two types of needs for a period of 10'':
 if T1+T2 flash: grease filter maintenance;
 if T1+T3 flash: odour filter maintenance.
During the 10'' it is possible to reset the grease filter by pressing
T1+T2 and to reset the odour filter by pressing T1+T3. After the
reset, the button combinations will flash rapidly twice. The interface
will now work as normal.
Please note:
During the 10", the hood will work normally but without any visual
feedback regarding the speed buttons. If during the 10'' no
operations are carried out, the LEDs will stop flashing and the
visual feedback will return to normal.
Maintenance
Cleaning
Clean using ONLY a cloth dampened with neutral liquid
detergent. DO NOT
INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Grease filter
Fig. 18
Traps cooking grease particles.
The grease filter must be cleaned once a month using non
aggressive detergents, either by hand or in the dishwasher,
which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolor
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 19
It absorbs unpleasant odors caused by cooking.
The saturation of the charcoal filter occurs after more or less
prolonged use, depending on the type of cooking and the
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four months.
The charcoal filter may NOT be washed or regenerated.
Circular charcoal filter
Apply one on each side as cover to both the shield grids of the
motor impeller, then turn clockwise.
For the disassembly, turn counter-clockwise.
Replacing lamps
The hood is equipped with a lighting system based on LED
technology.
The LEDs guarantee an optimum lighting, a duration up to 10
times longer than the traditional lamps and allow to save 90%
electrical energy.
For replacement, contact the technical service.
19
CLEAN WITH TOOLS OR