Publicidad
Idiomas disponibles
Idiomas disponibles
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
Package contents
The package contains:
1 Partly assembled machine
1 Box containing:
1 Combined rip and mitre fence
1 Fence bracket
1 Riving knife
1 Upper blade guard
1 Push stick
1 Spanner 13/17 mm
1 Spanner 20/22 mm
1 Allen key 4 mm
1 Allen key 5 mm
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description (fig. A)
Your ETS41 saw bench has been designed to saw wood in two different
modes to perform the four main sawing operations of ripping, cross-
cutting, bevelling and mitring easily, accurately and safely.
Ripping mode
In the ripping mode, the machine is used to perform the standard ripping
operation and for sawing wide pieces by manually feeding the workpiece
into the blade.
Blade traverse mode
The blade traverse mode is used to perform all cross-cutting and mitring
operations in which the workpiece is held stationary and the blade passed
through.
A1
1 Table
2 Table insert
3 Upper blade guard
4 Combined rip and mitre fence
5 On/off switch
6 Combined elevating handle and traverse handle
7 Rip and mitre fence guide support bracket
8 Riving knife
9 Saw blade
10 Blade level locking ring
11 Ripping position locating lever
12 Bevel scale
13 Bevel locking handle
14 Push stick
Optional attachments and accessories
A2
15 Legstand
18
A3
16 Extension table
A4
17 Parallel fence
A5
18 Sliding table with long mitre fence end stop
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an Elu
authorized repair agent or a qualified electrician.
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2), blue is for
Neutral (N) (4) and green/yellow is for Earth (E).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or
.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm
2
. When using a cable reel, always unwind the
cable completely. Also refer to the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
Voltage
Amperes
Cable rating (Amperes)
230
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
E N G L I S H
25
30
45
60
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
en - 3
Publicidad
