Storage Recommendations; Assembly And Adjustments; Installing And Removing The Battery Pack - MAG TOOLS BWP152 Manual De Instrucciones

Storage Recommendations

1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
the tool off, release the trigger switch. Your tool is equipped
with a brake. The anvil will stop when the trigger switch
is fully released. The variable speed switch enables you to
select the best speed for a particular application. The more
you squeeze the trigger, the faster the tool will operate. For
maximum tool life, use variable speed only for starting holes
or fasteners.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
direction of the tool and also serves as a lock off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool. To select reverse, depress the forward/
reverse control button on the left side of the tool. The
center position of the control button locks the tool in the off
position. When changing the position of the control button,
be sure the trigger is released.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. B)
nOTE: For best results, make sure your battery pack is
fully charged.
1
. To turn
2
determines the
6
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
5
button and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. C)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
4
handle .
Worklight (Fig. A)
7
There is a worklight located on the foot of the tool. The
worklight is activated when the trigger switch is depressed,
and will automatically turn off 20 seconds after the trigger
switch is released. If the trigger switch remains depressed,
the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector
allows you to select one of two speeds or the Impact Assist
mode. Select the speed/mode based on the application
and control the speed of the tool using the variable speed
1
trigger switch .
Impact Assist™ (Fig. D)
In addition to normal impacting modes, this tool features
the Impact Assist™ mode which grants the user greater
control in both fastening and loosening applications.
To enable Impact Assist mode, place the mode selector
on the foot of the tool in the middle position. When in
Impact Assist mode and operating in forward, the tool
will fasten at 1900 RPM until impact begins. The tool will
then pause for 0.75 seconds before continuing to impact
at a rate of 2400 IPM, providing the user with greater
control and reducing the chance of overtightening or
damaging material.
When operating in reverse, the tool will impact at a normal
speed and rate of 2400 IPM. Upon sensing that the fastener
has broken free, the tool will cease to impact and will
reduce speed to help prevent "run-off" of loose hardware.
MODE sElECTiOn
Low Mode Normal Impacting
High Mode High Speed Impacting RPM
Impact Assist Mode Impact Assist
English
into the tool handle, align the
9
which
RPM 0–400
0–1900
RPM 0–1900
9