Installation Notes - Multiplex RX-12-DR compact M-LINK Manual De Instrucciones

Press the 3-D digi-adjuster briefly, and select the priority
address (0 ... 15).
Press the 3-D digi-adjuster briefly.
Switch to the menu:
"4-6 Go back ...to RX M-LINK" /
"4-6 Zurück ...zu RX M-LINK"
(= back ... to RX M-LINK)
and confirm by pressing the 3-D digi-adjuster.
Select the menu point:
"4-10 Send data" / "4-10 Dat. senden"
(= Send data)
and hold the 3-D digi-adjuster pressed in:
The MULTImate displays:
"please wait..." / "bitte warten..." (= please wait).
Release the 3-D digi-adjuster:
When the Send process is complete, the screen
displays "--> OK!" (= complete!).
Disconnect the receiver, switch off the MULTImate.
2. Activating using the MULTIPLEX Launcher:
At "Sensor addresses" / "Sensorparameter"
(= Sensor address) auswählen:
"Address w/prio 1:" / "Adresse mit Prio 1:"
(= Address with priority 1).
Select the "Address" / "Adresse" (= Address) check-box,
and enter the desired address (0 ... 15).
Click on the "Accept" / "Übernehmen" button
(= Accept).
Click on the "Send data" / "Daten senden" button
(= Send data).
Click on the "Close" / "Beenden" button
(= Finish).
Close the MULTIPLEX Launcher, disconnect the
receiver.
This is the procedure for disabling the priority address:
1. Disabling using the MULTImate:
At the menu point "4-6 Sensor addr." / "4-6 Sensoradr."
(= Sensor address) select the option:
"4-6 Prio address" / "4-6 Prio Adresse"
(= Priority address).
! Note:
The second line of the screen displays the selected
priority address.
Hold the 3-D digi-adjuster pressed in:
The screen entry in the second line changes to:
"L off" / "L aus" (= L off).
Switch to the menu:
"4-6 Go back ...to RX M-LINK" /
"4-6 Zurück ...zu RX M-LINK"
(= back ... to RX M-LINK)
and confirm by pressing the 3-D digi-adjuster.
Select the menu point:
"4-10 Send data" / "4-10 Dat. senden"
(= Send data)
and hold the 3-D digi-adjuster pressed in:
The MULTImate displays:
"please wait..." / "bitte warten..." (= please wait).
Release the 3-D digi-adjuster:
When the Send process is complete, the screen
displays "--> OK!" (= complete!).
Disconnect the receiver, switch off the MULTImate.
Operating Instructions for
RX-7/9/12-DR compact M-LINK M-LINK 2.4 GHz receivers
Page 18
2. Disabling using the MULTIPLEX Launcher:
At "Sensor addresses" / "Sensorparameter"
(= Sensor parameters) auswählen:
"Address w/prio 1:" / "Adresse mit Prio 1:"
(= Address with priority 1).
Clear (erase) the tick in the "Address" / "Adresse" check-
box (= Address).
Click on the "Accept" / "Übernehmen" button
(= Accept).
Click on the "Send data" / "Daten senden" button
(= Send data).
Click on the "Close" / "Beenden" button
(= Finish).
Close the MULTIPLEX Launcher, disconnect the
receiver.
14. I
NSTALLATION
Protect your receiver from vibration, especially in models
powered by an internal-combustion engine (e.g. pack it loosely
in foam).
Locate the receiver at least 150 mm away from electric mo-
tors, petrol engine ignition systems and any other electronic
components such as speed controllers for electric motors and
drive batteries. Do not route the aerials close to these compo-
nents.
Install the receiver in the model in such a way that both
aerials are as far away as possible from electrically conduc-
tive materials, and are arranged at an included angle of 90°.
Locate the two aerial ends as far from each other as possible.
If the model's fuselage contains conductive material (e.g.
carbon fibre), the aerials must be installed in such a way that
the active part of the aerial (approximately the last 30 mm) is
located outside the model.
Do not deploy the receiver aerials inside or on model com-
ponents which are laminated or reinforced with electrically
conductive materials (metal foil, carbon fibre, metallic paints
etc.), as they have a shielding effect.
Do not shorten or extend the aerial or the aerial feed cable.
Never attempt to replace or repair the aerial or aerial cable!
Do not deploy the aerials parallel to servo leads, high-current
cables or electrically conductive parts (e.g. pushrods).
Keep to the recommended installed arrangements (
sketches A - D)!
High-current cables, e.g. those attached to the speed con-
troller, motor and flight battery, should be kept as short as
possible.
If you are using a diode-based battery backer, always install a
PeakFilter (# 8 5180).
Reception quality can be optimised by fitting a special ferrite
ring (# 8 5146) or suppressor filter lead (# 8 5057) in the speed
controller cable. It is also advisable to fit effective suppressors
to conventional (brushed) electric motors (not brushless types)
(e.g. use the suppressor set # 8 5020).
N
OTES
20.,