Adjustment - KNOVA KN M-2504RC Manual Del Usuario

ADJUSTMENT

RIP FENCE ADJUSTMENT (FIG. Z)
1. The fence (1) can be repositioned by lifting up the
handle (2) and sliding the fence to the desired location.
Pushing down the handle locks the fence in position.
2. Position the fence (1) on the right side of the table, and
along one edge of the miter gauge grooves.
3. Lock the fence handle (2). The fence should be parallel
with the miter gauge groove.
4. If adjustment is needed to make the fence parallel to the
groove, do the following:
• Loosen the two screws (3) and lift up on the handle (2).
• Hold the fence bracket (4) firmly against the front of
the saw table. Move the rip fence until it is parallel with
the miter gauge groove.
• Tighten both screws and push the handle to lock.
5. If fence is loose when the handle is in the locked
(downward) position, do the following:
• Lift the handle (2) upward and turn the adjusting
nut (5) clockwise using a 10 mm wrench until the rear
clamp is snug. Do not turn the adjusting nut more than
1/4 turn at a time.
• Over-tightening the adjusting nut will cause the fence
to come out of alignment.
WARNING
Failure to
properly align the
fence can cause
"kickback" and
5
serious injury
could occur.
RIP FENCE INDICATOR
ADJUSTMENT
(FIG. Z-1)
1. The rip fence
indicator (1) points
to the measurement
scale (2). The scale
shows the distance
from the side of the
fence to nearest
side of the blade.
2. Measure the actual
distance with a rule.
If there is a difference
between the
measurement and
the indicator, adjust
the indicator (1).
3. Loosen the screw (3)
and slide the
indicator to
the correct
measurement
on the scale (2).
Tighten the screw
and remeasure
with the rule.
4
2
1
2
3
ADJUSTING MITER GAUGE (FIG. AA)
1. Loosen the lock handle (1) to allow the miter body (2) to
rotate freely. Position the miter body (2) at 90° so the
positive detent secures its position. Tighten the lock
handle to hold the miter body in position.
2. If the pointer (3) requires
adjustment, loosen the screw (4)
with a screwdriver. Adjust the
pointer to 90° on the scale, then
firmly tighten the adjustment
screw.
3. To change angles on the miter
gauge, loosen the lock handle (1)
and rotate the miter body (2) to
the desired angle as indicated
by the scale. Secure in position
by tightening the lock handle (1).
ADJUSTING THE TABLE
INSERT (FIG. BB)
WARNING
To avoid serious
injury, the table insert (1)
must be level with the
table. If the table insert is
not flush with the table, adjust
the two bolts (2) with a 4 mm
hex wrench until it is parallel with the table.
Fig. Z
NOTE: To raise the insert, turn the hex screws
counterclockwise, to lower the insert, turn the hex screws
clockwise. Do not remove the insert, adjustments need to be
made with the insert in place to get the proper level.
1
3
ADJUSTING THE 90° AND 45° POSTIVE STOPS
(FIG. CC, DD)
Your saw has positive stops that will quickly position the saw
blade at 90° and 45° to the table. Make adjustments only if
necessary.
90° Stop
1. Disconnect the saw from the power source.
2. Raise the blade to the maximum elevation.
Fig. Z-1
3. Loosen the blade lock knob and move the blade to the
maximum vertical position and tighten the blade lock
14
knob.
3
2
Fig. AA
2
1
4
1
1
Fig. BB