YATO YT-82829 Manual Del Usuario página 17

GB
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains.
In addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (II), the more LEDs will light up, the more
fully the battery pack is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (II).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
ASSEMBLY OF EQUIPMENT ELEMENTS
Assembly of the abrasive wheel guard
For this purpose, you should put on the wheel cover on the cylindrical body part around the spindle and with a screw or clip of
cover ring clamp, immobilize it, so the cover will be mounted straight ahead, fi rmly and tightly. Set the guard of the grinding wheel,
so the unsheltered part of the grinding wheel will be as far as possible from the hand of a grinder user. Never work with the grinder
without correctly mounted grinding wheel guard!
With the grinder there is supplied the guard, which provides the adequate protection only when grinding with abrasive wheels and
wheels using sandpaper and some wire brushes. After installing the wheel on the spindle, the accessory must not protrude beyond
the side guard. In the case of performance of any other type of allowed work, you should contact the manufacturer to acquire the
guard intended for this kind of work.
Installation of auxiliary handle
Mount the handle by its fi rm screwing to the tool heading. The handle has a socket, which allows to store the wrench for fi xing
the grinding wheel. This makes it easier to store the wrench. After completion of all works requiring to use the wrench it should be
inserted in the socket and you should make sure that it does not slip spontaneously by its own weight.
OPERATION OF THE GRINDING WHEELS
ATTENTION! Mounting of the abrasive wheels may be done only with disconnected power supply. Remove the battery pack
from the power tool socket!
Installing the wheels
Disconnect power supply voltage from the tool. Remove the battery pack from the power tool socket!
During the assembly please pay attention, that the edges A (IV) at the bottom of the spindle shaft and of the mounting fl anges
exactly overlap.
Install the top mounting fl ange on spindle,
Mount the grinding wheel on the spindle and on the upper mounting fl ange.
Screw the bottom mounting fl ange on the spindle.
Press the spindle lock and tighten the lower mounting fl ange with a key and then release the lock button.
Mount the battery to the power tool, turn on the grinder and watch its work without any load by the time of about 1 minute.
Remove the battery and inspect the wheels mounting.
The location of the mounting fl anges
Please pay attention, that grinding wheels, in the point of mounting to the spindle, can vary in their thickness.
Depending on the applied grinding wheels, which are thin (thickness up to 3.2 mm), or thick (thickness above 3.2 mm) the position-
ing of mounting fl anges (III) is diff erent. Do not use wheels thicker than 6 mm.
Removing the grinding wheels
Turn off the grinder and remove the battery.
Press the spindle lock and loosen the lower mounting fl ange with the wrench for mounting, and then remove the abrasive wheel
O R I G I N A L I N S T R U C T I O N S
17