Mm / 2- 1 - Triton TTS 1400 Instrucciones De Uso

Ocultar thumbs Ver también para TTS 1400:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 55
Type of material
Solid wood (hard or soft)
Chipboard
Laminated wood,
blockboard, veneered
& coated board
Hardboard
Assembling and fixing the track
• For guidance on assembling and securing the track and
use of other accessories, please see the 'Accessories'
section of this manual. Pages 10-11
Using the fine adjustment cams
• The Fine Adjustment Cams (9 and 15) enable you to
remove excessive play between the track and the saw
to ensure cutting accuracy as the saw moves along the
track
1. Loosen the knobs securing the front and rear Fine
Adjustment Cams (9 and 15)
2. Place the saw in the track
3. Adjust the cam levers so that they remove excessive
play, then re-tighten the knobs to secure the levers in
position
NOTE: The cams are fully engaged when the levers are at
the rear of their slots
Anti-kickback
• Kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece towards the operator
• The anti-kickback feature on this saw prevents injury
to the user if the saw unexpectedly kicks back
1. Rotate the Anti-Kickback Knob to the '0' position
(before you place the saw in the track)
2. When you slide the saw onto the guide rail of the track,
the anti-kickback feature is automatically engaged
NOTE: If kickback does occur, check that the guide rail is
not damaged before continuing with the cut
CUTTING
IMPORTANT
• Check that the workpiece and track are properly
supported and secured so that movement cannot occur
whilst the saw is in operation
GB
• Always hold the machine with both hands using the
front and rear handles
• Always push the saw forwards. NEVER pull the saw
backwards towards you
• Wear all safety equipment required to use this tool.
See 'Safety'
Operating Instructions
8
1. Check that the Track Lock (14) and Anti-Kickback Knob
Speed setting
4-6
2. Engage the front of the saw in the track
5-6
3. For a bevel cut, lock the saw to the track by rotating
2-5
4. Rotate the Mode Selection Lever (20) to
1-4
5. Hold the saw firmly with both hands and squeeze the
6. Allow the blade to reach full speed, then depress the
7. Push the saw forward along the track to engage the
8. Maintain a consistent feed rate - too fast may put
9. After completing the cut, release the trigger switch
Making bevel cuts
IMPORTANT: When making bevel cuts it is essential to
lock the saw in the track:
1. Rotate the Track Lock (14) to the 'I' position to lock the
Making plunge cuts
1. Use the Width of Cut Indicators (23) to position the saw
2. Hold the saw firmly with both hands and squeeze the
3. Allow the blade to reach full speed, then depress the
4. Make your cut, again using the width of cut indicators
5. Allow the blade to come to a complete stop before
(10) are in the '0' position
the Track Lock (14) to the 'I' position
free plunge position
for a scribe cut
Trigger Switch (5)
Plunge Lock Button (2) and plunge the blade to your set
depth
blade with the workpiece and start the cut
excessive strain on the motor, while too slow may
burnish your workpiece. Avoid any sudden movements
of the saw
and allow the blade to come to a complete stop before
removing the saw from the track
saw in the track
on the track where you need the blade to engage the
workpiece
Trigger Switch (5)
Plunge Lock Button (2) and pivot the saw forward to
plunge the blade into the workpiece to the set depth
as a guide to when to raise the saw from the workpiece
removing the saw from the track
or scribe mode

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido