Chicco oasys 1 isofix Instrucciones De Uso página 21

backrest of the car seat (Diag. 12) to ensure
maximum adherence.
How to fit the top tether
The installation of the child car seat is
complete only by fitting the Top Tether.
WARNING! Pease refer to the instructions
booklet of the vehicle to identify the locking
point of the Top Tether of the child car seat.
This locking point is indicated by a special
label (Diag. 13), and it may be located in the
positions indicated in diagrams 14a – 14b –
14c – 14d.
WARNING! Check that the Top Tether is
locked with the correct locking device. Do not
mistake the locking device of the Top Tether
with the ring provided for securing luggage
(diag. 15).
WARNING! Insert the Top Tether between the
top part of the backrest of the car seat and the
headrest. Never insert the Top Tether above
the car headrest (diag. 16).
8. After identifying the locking point, connect
the hook (DD) of the Top Tether to it (diag. 17.
pulling the strap firmly to tension it correctly
(diag. 18). The belt is tensioned correctly when
the indicator located on the strap is green
(diag. 19).
10. Roll up the excess strap and fasten it with
the specific Velcro strap provided (diag. 20).
REMOVAL INSTRUCTIONS
WARNING! Remove the child from the child
car seat before commencing.
1. Loosen the Top Tether by pressing the
appropriate button BB (diag. 21), then
disconnect the hook DD.
2. Roll up the Top Tether strap and fasten with
the specific Velcro strap provided (diag. 20).
3. Pull the ISOFIX system unlocking handle
outwards and, whilst keeping hold of it (diag.
22) lift the child car seat away from the vehicle
seat until it disconnects from the ISOFIX
system (diag. 23).
4. Push the two red buttons (V) inwards and
release the connectors from the corresponding
ISOFIX locking devices, located on the car seat
(diag. 24).
All manuals and user guides at all-guides.com
5. Remove the two previously stored caps
(U) from the compartment between the seat
and the backrest (Diag. 25) and reinsert them
in the related ISOFIX connectors, paying
attention that the two ends are facing inside
(Diag. 26).
6. Push the ISOFIX system inside the base of
the child car seat, inserting it completely into
the base.
SEATING THE CHILD IN THE CHILD CAR
SEAT
Before sitting your child in the child car seat,
at the same time, hold the two child car seat
harnesses under the shoulder straps, and pull
them in your direction to slacken them (Diag.
27).
- Unfasten the buckle (F) of the child car seat
harnesses by pressing the red button (Diag.
28), and pull the harnesses in an outward
direction. Now the child can be placed in the
child car seat (diag. 29).
harnesses, overlap the two buckle straps (diag.
30a - 30b) and push them together firmly
inside the buckle slot, until a "click" is heard
(diag. 31).
HOW TO REMOVE THE CHILD FROM THE
CHILD CAR SEAT
To remove the child from the child car seat,
press the red button on the buckle (F) and
release the restraint harness.
ADJUSTING
HARNESSES
The height of the headrest and restraint
6 positions by pressing the button located at
the rear (M).
headrest must be fitted so as to allow that the
harnesses come out from the backrest at the
height of the child's shoulders (diag. 32). To
(M), located at the rear of the backrest (diag.
33) and, at the same time, slide the headrest
until the desired position is reached (diag. 34);
21
- Position the crotch strap correctly, take the
THE HEADREST AND