Setting Oscillating Frequency; Cleaning & Maintenance; Environmental Protection - Metabo SRE 4350 TurboTec Manual Original

en ENGLISH
6.2 Installation of sanding sheet
Sanding sheet with velcro-type fastening
Simple attachment and removal thanks to the velcro-
type fastening. Simply press on the sanding sheet
such that the holes in the sanding sheet (10) and
sanding plate (12) are aligned.
Sanding sheet without velcro-type fastening
Secure the sanding sheet using a clamping element
(11). Pull the disc across the sanding plate (12) so it
is taut; then fasten in place with the other clamping
element
7. Use
7.1 On/Off switch, continuous activation
To start the machine, press the trigger (5).
For continuous operation the trigger can be locked
with the lock button (4). To stop the machine, press
the trigger (5) again.
7.2

Setting oscillating frequency

When the TurboBoost switch (3) is switched off, the
oscillating speed can be set at the setting wheel (2).
This is also possible during operation.
Recommended oscillating frequency settings:
Plastic materials . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Metal, Plexiglas
®
Coarse and fine sanding, wood . . . . . . . . . . . 5
The best way to determine the ideal setting is through
a practical trial.
7.3 TurboBoost switch
Actuate the TurboBoost switch (3) during operation to
switch on additional power reserves for maximum
material removal rate.
7.4 Dust extraction
To optimise the dust extraction performance, fit the
sanding sheet such that the holes on the sanding
sheet (10) and sanding plate (12) are aligned.
Note: We recommend connecting a suitable
extraction device when sanding abrasive material
(e.g. plaster, etc.).
Own extraction units:
Fit dust bag (8) to the ejection nozzle (7). Pull the
dust bag (8) backwards to remove it.
Empty the dust bag (8) in good time to optimise dust
extraction.
Third-party extraction units:
Connect a suitable extraction device to the ejection
nozzle (7).
8
, old coats of paint . . . . . . . . 3-4
8. Cleaning, Maintenance
- Emptying the dust bag: remove the closure band
(9). Empty the dust bag (8), clean with an extrac-
tion device if necessary. Close the dust bag again
with the closure band (9).
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the motor.
Replacing worn sanding plate (12)
- Remove fixing screws (on lower side of sanding
plate).
- Take off sanding plate.
- Sanding plate (as a spare part), see page 2.
- Mount sanding plate.
- Re-insert the fixing screws on the lower side of the
sanding plate (the screw must be inserted in the
existing thread pitch) and tighten (tightening torque
= 3.5 Nm +/- 0.2 Nm).
9. Accessories
Use only genuine Metabo accessories.
Note: Metabo accessories are adapted to suit the
machine's velcro-type fastening. This increases the
service life of the velcro-type fastening.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
10. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If the mains connection cable of this machine is
damaged, it must be replaced by the manufacturer or
an authorized service centre to avoid hazard.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

11. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of power
tools in your household waste! In accordance
with European Guideline 2012/19/EU on used
electronic and electric equipment and its implemen-
tation in national legal systems, used power tools
must be collected separately and handed in for envi-
ronmentally compatible recycling.