Infl Ation Instructions; Using The Boat - Gumotex SEAWAVE Manual Del Usuario

SPECIAL ACCESSORIES:
(These may be bought with the kayak)
- Three-seat version infl atable seat
- Covering board

3. Infl ation Instructions

Roll out the kayak. Slip the tracking fi n into the bottom an-
chor point (15) Infl ate seats and footrests before assembling.
Fig. 2 shows the valve (10) handling. Assemble seats and
footrests on the defl ated kayak.
Thanks to its design, the SEAWAVE kayak may be used in
one-, two-, or three-seat versions - Refer to Fig. 1.
One-seat version assembly:
Fix the seat (7) into the bottom anchor point (16). Pull the seat
backrest straps (19) through the seat anchor points (17) on
side chambers marked as <1>. Pull the strap ends through
the plastic buckle (20) - Refer to Detail A. Fix the footrest
sized 34x16 mm (8) to the second position in the bottom
anchor point (16), pull the strap through the bottom plastic
buckle and tighten it. Correct pulling of the strap through the
buckle is shown in Detail B.
Two-seat version assembly:
Fix the front and rear seats (7) in the bottom anchor point
(16). Pull the seat backrest straps (19) through the seat an-
chor points (17) on side chambers marked as <2>. Pull the
strap ends through the plastic buckle (20) - Refer to Detail
A. Fix the footrest sized 34x16 mm (8) to the fi rst position in
the bottom anchor point (16), fi x the footrest sized 45x19 mm
(9) to the third position in the bottom anchor point (16), pull
the strap through the bottom plastic buckle and tighten it.
Correct pulling of the strap through the buckle is shown in
Detail B.
Three-seat version assembly:
Fix the seats (7) into the bottom anchor point (16). Pull the
seat backrest straps (19) through the seat anchor points
(17) on side chambers marked as <3>. Pull the strap ends
through the plastic buckle (20) - Refer to Detail A. In this ver-
sion, use the front footrest sized 34x16 mm (8) only fi x it to the
fi rst position in the bottom anchor point (16), pull the strap
through the bottom plastic buckle and tighten it. Correct
pulling of the strap through the buckle is shown in Detail B.
Infl ate the air chambers in sequence: Side chambers (1),
the bottom (2). Use a foot-pump or piston pump with valve
adaptor for infl ating - Refer to Fig. 2b (the adaptor is in-
cluded in the kayak bonding set). Check the condition of the
valves before infl ating. Tighten the valves with the assembly
key - see Fig. 2c. Set the valves to the OFF position. Valve
handling - Refer to Fig. 2. Infl ate the air chambers until they
are fi rm but not completely stiff . The air chambers should
provide a feeling comparable to squeezing a ripe orange.
You can check the exact operating pressure by using a suit-
able pressure gauge (optional accessory) – see Figure 2a.
For transferring the kayak, use the handle (12) on the front
and rear board.
ATTENTION
The maximum operational pressure in air chambers is
0,025 MPa. The operational pressure at the bottom is lim-
ited by the overpressure valve. If the ambient temperature
increases (e.g. owing to sunlight), the pressure in the air
chambers of the boat can rise rapidly. we recommend re-
leasing some air from all air chambers of the canoe after
pulling it out of the water. This will prevent possible destruc-
tion of the air chambers. However, do not forget to continu-
ously check air pressure in the chambers afterwards, too.
A corresponding reduction in operating pressure is up to
20 % within 24 hours.
ATTENTION
when using the boat, always seal the valves with their
valve caps. This will keep dirt out of the valves. Dirt can-
cause leaky valve seals.

4. Using the Boat

The SEAWAVE kayak is designed for recreational use and
water tourism.
Whenever the kayak is used on waterways, Waterway Traffi c
Rules should be observed. Operation of the SEAWAVE a in-
fl atable kayak does not require any licence provided the
people who operate the canoe know the techniques of small
boat operation within the scope necessary for its operation,
as well as the valid navigation rules of the particular country.
The SEAWAVE kayak can be used on still or gently fl owing
waters up to Diffi culty Grade WW 2. This is only a recom-
mended use, it always depends on the specifi c abilities of
the user! Use double-bladed kayak paddles with a length of
approx. 210 cm. People travelling in the kayak should sit in
their seats and wear fl otation life-jackets.
The manufacturer recommends using the boat in suffi cient
water condition (see Control table - draught).
ATTENTION
Prior to every use of the boat, check whether it is neces-
sary to observe any special regulations, restrictions or
rules connected with the river, surface of water or area in
which you aim to operate.
The boat is not intended for towing a motor boat, it must
not be slipped or otherwise excessively stressed. In case
of emergency, use the handle to at bow of the boat to tow.
Sharp edged and pointed items carried in the boat must
be safely wrapped.
Place all valuables into a waterproof container and fas-
ten it to the boat.
Over time, sunlight adversely aff ects the rubber coating
of the boat; therefore, it is advisable to store the boat in
shade each time after use.
CAUTION:
• On large surfaces of water (seas, lakes) pay attention
to water currents and off -shore breezes. Currents and
breezes may make it impossible to return to shore.
• The SEAwAVE kayak should not be used in poor con-
ditions, such as In reduced visibility (night, fog, rain).
Specifi cations of the ww 2 diffi culty grade - moderately
diffi cult:
• irregular waves and currents, rapids of moderate diffi cul-
ty, weak eddies and whirls, low gradients, small rapids in
heavily meandering or badly transparent watercourse
• regular current and low regular waves, small rapids, sim-
ple obstacles, frequent meanders with rapidly fl owing
water.
ATTENTION
Pay extra attention to your choice of fl otation life-jacket. Pay extra attention to your choice of fl otation life-jacket.
The fl otation life-jacket should have a tag bearing details The fl otation life-jacket should have a tag bearing details
of its fl otation capabilities and safety certifi cation. of its fl otation capabilities and safety certifi cation.
9