Fader Start - Denon DN-X800 Manual De Instrucciones

FADER START

5
If the separately sold DN-1800F, DN-2100F and DN-2600F players are connected to CH-3 or CH-4, they can be started using the
source input fader (Ch. fader) or Crossfader, as long as the 3.5 mm stereo mini cords have been connected.
DN-X800
MIC 1
PH1/LN1
0 10 ON/OFF MIN MAX MIN MAX
DIGITAL1 LINE2
MAIN MIC GAIN GAIN
MIC POST
CH FADER START
-26dB +10dB ON/OFF -26dB +10dB -26dB +10dB
HI HI 10 HI
8
6
-26dB +10dB
-26dB +10dB -26dB +10dB
MID MID 4 MID
3.5 mm stereo
2
0
-26dB +10dB -26dB +10dB -26dB +10dB
mini cord LOW LOW LOW
CROSS
FADER
START A
SAMP.
0 10 ON/OFF
AUX MIC
H/S
CROSSFADER
BRAKE
CH FADER START CONTOUR
X
2
1 3
H/S 2 A
OFF 4
ON OFF
H/S 1
ASSIGN A
TRACK M S F
OPEN/ PITCH
CLOSE
T. REMAIN ELAPSED SINGLE CONTINUE
1
PITCH
SEARCH SCAN
PITCH BEND
PITCH%
JOG CONT./
MODE SINGLE TIME CUE PLAY/PAUSE
TRACK
CUE
1
CD1
Fader jack
DN-1800F
NOTE:
Use the analog inputs/outputs when the DN-1800F, the DN-2100F and the DN-2600F are moved by FADER START.
CH3 CH4
Fader jack Fader jack
2 3 4
- 20 15 10 7 5 3 1 0 1 3 5 8 +
L
PH2/LN3 PH3/LN5 LINE7 CUE
R
PWR
PGM
- 20 15 10 7 5 3 1 0 1 3 5 8 +
MIN MAX MIN MAX
DIGITAL2 LINE4 DIGITAL3 LINE6 DIGITAL4 LINE8 ZONE MASTER SUB WOOFER
GAIN GAIN
CH FADER START CH FADER START CH FADER START
10
-26dB +10dB -26dB +10dB 0 10 MIN MAX
10 HI 10 HI 10 LEVEL FREQ.
8
METER EFFECT LOOP
8 8 8
6
6 6 6
4
-26dB +10dB
-26dB +10dB BOOTH
4 MID 4 MID 4
2 MAIN
3.5 mm stereo
2 2 2
0
0 0 0
-26dB +10dB -26dB +10dB 0 10
LOW LOW LEVEL mini cord
MIC
DIGITAL
CUE
CROSS
FADER
START B
SAMP.
CH 1 CH 2 CH 3 CH 4 RESET
H/S
BRAKE L-CUE
X MONO R-PGM
2
1 3
B H/S 2
OFF 4
CUE PGM 0 10
STEREO
H/S 1 PAN CUE/PGM LEVEL
ASSIGN B PHONES DJ MIXER
TRACK M S F
OPEN/ PITCH
CLOSE
T. REMAIN ELAPSED SINGLE CONTINUE
2
PITCH
SEARCH SCAN
PITCH BEND
PITCH%
0% 0%
JOG CONT./
MODE SINGLE TIME CUE PLAY/PAUSE
TRACK
CUE
REMOTE CONTROL UNIT RC-47
OPEN/CLOSE OPEN/CLOSE
2
1 2
CD2
Fader jack
POWER
ON OFF
Channel Fader Start
Turn on the Ch. fader start switch.
CH FADER START
1
ON OFF
Move the source input fader (Ch.
CH FADER START
fader) of CH-3 or Ch-4 control all
10
the way to the bottom.
8
2
6
4
2
0
DN-1800F
Set the cue point on either drive.
3
DN-2100F and DN-2600F
Set the A-1 or A-2 point on either drive.
When you want to start the
CH FADER START
player, move up the source input
10
fader (Ch. fader) and the CD
player will begin playing.
8
4
6
4
2
0
NOTES:
• Channels selected with the Crossfader Assign A, B
switches and the Crossfader Start A, B buttons cannot
be started with the source input fader (Ch. fader).
• Ch. Fader Start and Cross Fader Start for the same
source will not operate simultaneously. You must select
from either one. If both Ch. Fader and Cross Fader
switches are ON, priority will be the cross fader.
ENGLISH
Crossfader Start
Using the Crossfader Assign A B switches, select
1
the channel (CH-3 or CH-4) that the CD player is
connected.
Press the Crossfader Start A, B buttons of the
2
channel connected to the CD player to be controlled.
Slide the Crossfader all the way in direction opposite
the source you want to start. ( In the following
example, startup is done with the CD player
connected to CH-3 set to Assign A. )
3
X
2
1 3
A
OFF 4
ASSIGN A
DN-1800F
Set the cue point on the left drive.
4
DN-2100F and DN-2600F
Set the A-1 or A-2 point on the left drive.
Use the Crossfader Contour control to control the
5
cross fader startup curve.
When the Crossfader is slid in the opposite direction
as in "3", CD player play will begin.
6
X
2
1 3
A
OFF 4
ASSIGN A
B
B
7