Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
WARNING
•
Disconnect power to tHe receptAcLe At tHe circUit BreAKer pAneL BeFore instALLinG.
• iF UsinG A power screwDriVer, Be cAreFUL not to oVer tiGHten tHe screws BecAUse
YoU wiLL strip tHe tHreADs in tHe JUnction BoX AnD/or tHe eLectricAL DeVice
This die cast cover can be used outdoors or in other wet locations when cover
is closed (protects receptacles while in use for unattended applications). The
cover is UL listed, CSA certified, Type 3R rated and meets National Electrical
Code requirements covered by 2011 NEC 406.9 (B) (1).
Contents
The following items are included:
• Weatherproof cover/base - pre-assembled.
• U niversal insert for duplex receptacles (model WP1030 includes a double
duplex insert)
• U niversal insert for GFCI receptacles (model WP1030 includes a double GFCI
insert)
• G asket with slits for mounting screws
• B aggie assembly with mounting hardware
Models
The instructions cover these models:
wp1010MXD, wp1250MVXD, wp3110MXD
Single gang vertical mounting only
wp1010HMXD
Single gang horizontal mounting only
wp1030MXD, wp1250MXD
2-gang, 2 device horizontal or vertical installation
Installation
Follow the steps listed below while referring to the illustrations for your
particular model.
1. If installation is being done on an existing receptacle(s), remove the
existing cover and discard.
2. The mounting screws that hold the receptacle or GFCI to the junction box
can be removed. Do not remove the receptacle wiring connections.
3. Select the correct insert for your application and press into base.
4. Locate the gasket as required for the installation. The gasket can be
temporarily held to the back of the base/insert assembly using the
mounting hardware provided. The receptacle cover should be installed on a
smooth, flat, non-porous surface.
To ensure a weatherproof seal on irregular surfaces such as brick or cedar
siding, a 1/4" bead of non-hardening silicon caulk compound (neoprene,
urethane or polyurethane type) should be placed between the weather-
proof receptacle gasket and the mounting surface.
5. M ount the base/insert assembly and the receptacle(s) to the junction box
using two of the long screws provided (do not over-tighten).
To ensure weatherproof protection, the cover must be installed so that the
hinge points are located at the top.
6. If mounting to an outdoor junction box or FS box, use the remaining long
screws, 2 or 4 screws as required, to further secure the cover and insert
assembly to the junction box. Note that holes are located in the insert
for mounting to an FS box or any standard single gang box. For specially
designed junction boxes, holes should be carefully drilled to line up with
the holes in the box to accommodate mounting.
7. Be sure all screws are secure but not over-tightened. Install the remaining
1 or 2 short screws into the receptacle(s) as required.
8. A hasp is provided to allow for padlocking the cover if desired.
FOR BEST PROTECTION FROM RAIN OR HUMIDITy, BE SURE TO ROUTE THE
CORDS THROUGH THE CORD OUTLETS IN THE COVER AND PRESS THE COVER
FIRMLy UNTIL IT SNAPS CLOSED OVER THE HASP.
Cover may be removed for ease of mounting and then reattached.
A grounding wire is provided for all models. The mounting screw that holds the receptacle or light switch should pass through the ring terminal on the end of the wire.
RISK OF ELECTRIC SHOCK
NOTICE
WP1000MX SERIES
WEATHERPROOF RECEPTACLE COVERS
FOR EXTRA DUTY APPLICATIONS
Single gang vertical Model
WP1010MXD, WP1250MVXD, and
WP3110MXD
Single gang horizontal
Model WP1010HMXD
2-gang horizontal or vertical
Model WP1030MXD and WP1250MXD
This 2 gang cover is designed for installation on 2-gang junction boxes. If
installing on a single gang box or a non-metallic junction box, you will need
to use the grounding wire (as shown on the Optional Grounding illustration).
If the junction box is non-metallic, a separate ground will need to be run and
connected to the grounding wire by cutting and removing the spade terminal,
stripping the ground wire and making a pigtail connection. Also note for single
gang installation you will need to purchase an Intermatic insert model #WP101
for duplex receptacle or WP102 for GFCI application.
The insert for model WP1030MXD and WP1250MXD may be oriented for
horizontally or vertically mounted receptacles and is designed for double duplex
or double GFCI applications.
Optional
Grounding
Optional Grounding
(Single gang
installation)
Publicidad
Manuales relacionados para Intermatic WP1000MX Serie
Resumen de contenidos para Intermatic WP1000MX Serie
- Página 1 Also note for single 8. A hasp is provided to allow for padlocking the cover if desired. gang installation you will need to purchase an Intermatic insert model #WP101 for duplex receptacle or WP102 for GFCI application.
- Página 2 8. Se incluye una aldaba para cerrar la cubierta con un candado si se desea. de inserción Intermatic modelo #WP101 para receptáculo tipo duplex o modelo PARA UNA MAYOR PROTECCION DE LA LLUVIA O DE LA HUMEDAD ASEGURESE #WP102 para aplicaciones de disyuntores diferenciales.
- Página 3 VEILLER À BIEN TIRER LES CÂBLES À TRAVERS LES PASSAGE DE CÂBLE DU être utilisé (comme indiqué sur l’illustration Mise à la terre en option). Si la boîte de COUVERCLE ET À APPUYER FERMEMENT SUR LE COUVERCLE DE MANIÈRE À jonction est non métallique, une terre séparée doit être tirée et raccordée au fil de L’ENCLENCHER SUR LE FERMOIR. terre. Pour cela, couper et retirer la cosse, dénuder le fil de terre et effectuer une Le couvercle peut être démonté pour faciliter la pose puis remonté sur son épissure en tortillon. Noter également que la pose d’un modèle simple nécessite boîtier. l’achat d’un insert Intermatic modèle WP101 pour une prise duplex ou WP102 pour un GFCI. L’insert pour les modèles WP1030MXD et WP1250MXD peut être orienté pour une pose sur des prises horizontales ou verticales et est destiné aux installations à double duplex ou double GFCI.
- Página 4 LIMITED ONE YEAR WARRANTY If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.