Changing The Light Bulb; Troubleshooting; Refrigerator Operation - Maytag W10857668C Instrucciones Para El Usuario

Changing the Light Bulb

IMPORTANT: The light bulbs in both the refrigerator and
freezer compartments use LED bulbs, incandescent bulbs or a
combination of the two. If the lights do not illuminate when the
refrigerator and/or freezer door is opened, call for assistance or
service. See "Warranty" for phone numbers.
1. Unplug the refrigerator or disconnect power.
2. Remove the light shield (on some models).
Top of the refrigerator compartment - Slide the light shield
■
toward the back of the compartment to release it from the
light assembly.
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual, or visit http://maytag.custhelp.com.
In Canada, visit www.maytag.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Maytag Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
The refrigerator will not operate
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power cord unplugged? Plug into a grounded 3 prong outlet.
■
Is outlet working? Plug in a lamp to see if the outlet is
■
working.
Household fuse blown or circuit breaker tripped? Replace
■
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
14

TROUBLESHOOTING

In Canada:

Refrigerator Operation

3. Replace the burned-out bulb(s) with a bulb of the same size,
shape and wattage.
To replace the burned-out LED bulb with a LED bulb, order
■
Part Number W10565137 (3.6 watts).
NOTE: Some LED replacement bulbs are not recommended
for wet/damp environments. The refrigerator and freezer
compartments are considered to be wet/damp environments.
If using a brand of LED bulb other than the recommended LED
bulb, before installation, read and follow all instructions on the
LED packaging.
When replacing an incandescent bulb, use only
■
incandescent bulbs for household appliances with a
maximum of 40 watts. Replace bulb shield/shroud after
replacing incandescent bulb.
4. Plug in refrigerator or reconnect power.
Maytag Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Are controls on? Make sure the refrigerator controls are on.
■
See "Using the Control(s)."
New installation? Allow 24 hours following installation for the
■
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to
its high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to
this reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with explanations.
Buzzing - heard when the water valve opens to fill the ice
■
maker
Pulsating - fans/compressor adjusting to optimize
■
performance
Hissing/Rattling - flow of refrigerant, movement of water
■
lines, or from items placed on top of the refrigerator
Sizzling/Gurgling - water dripping on the heater during
■
defrost cycle