Nailer Safety Warnings - Milwaukee 2740-20 Manual Del Operador

• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or
risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.

NAILER SAFETY WARNINGS

• Always assume that the tool contains fasten-
ers. Careless handling of the nailer can result in
unexpected firing of fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the
fastener causing an injury.
• Do not actuate the tool unless the tool is placed
firmly against the workpiece. If the tool is not in
contact with the workpiece, the fastener may be
deflected away from your target.
• Disconnect the tool from the power source when
the fastener jams in the tool. While removing a
jammed fastener, the nailer may be accidentally
activated if it is plugged in.
• Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while attempt-
ing to free a jammed condition.
• Do not use this nailer for fastening electrical ca-
bles. It is not designed for electric cable installation
and may damage the insulation of electric cables
thereby causing electric shock or fire hazards.
•Prior to each use, check workpiece contact and
trigger for correct operation. Do not disassemble
or clamp parts of the workpiece contact, trigger, or
driving mechanism. This will cause unexpected
actuation, resulting in serious injury.
•Do not engage in horseplay. The discharged
fasteners are projectiles capable of causing seri-
ous injury.
•Do not remove, tamper with, or otherwise cause
the tool operating controls to become inoper-
able. This will cause unexpected actuation, resulting
in serious injury.
•Do not operate a tool if any portion of the tool
operating controls is inoperable, disconnected,
altered, or not working properly. This will cause
unexpected actuation, resulting in serious injury.
•Always keep hands and body away from dis-
charge area of the tool. Never attempt to clear
a jammed workpiece contact by grasping the
discharge area of the tool. Fasteners discharged
from tool can cause serious injury if they contact
hands or body.
•Do not drive fasteners close to the edge of the
workpiece. Fasteners can slip off corners and
edges or penetrate through thin material, making
them projectiles capable of causing serious injury.
•Use the tool only for the intended purpose. Do
not abuse the tool. Do not use as a hammer, stamp
or engrave information onto parts, drop or impact
the tool or otherwise apply excess force to the tool
in use. Do not mount the tool to stands or modify it
for stationary use.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SPECIFICATIONS
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Cat. No. ...................... 2740-20 18 Ga Brad Nailer
Fastener Length ............... min 0.625" / max 2.125"
Collation Angle..................................................... 0°
Fastener Size (Diameter) ................... 18 Ga / 1.2 mm
Magazine Capacity ........................................110 nails
Cat. No. ..... 2741-20 16 Ga Straight Finish Nailer
Fastener Length ..................... min 0.75" / max 2.5"
Collation Angle..................................................... 0°
Fastener Size (Diameter) ................... 16 Ga / 1.6 mm
Magazine Capacity ........................................110 nails
Cat. No. .......2742-20 16 Ga Angled Finish Nailer
Fastener Length ..................... min 1.25" / max 2.5"
Collation Angle................................................... 20°
Fastener Size (Diameter) ................... 16 Ga / 1.6 mm
Magazine Capacity ........................................110 nails
Cat. No. ....................2743-20 15 Ga Finish Nailer
Fastener Length ..................... min 1.25" / max 2.5"
Collation Angle................................................... 34°
Fastener Size (Diameter) ................... 15 Ga / 1.8 mm
Magazine Capacity ........................................110 nails
3