Using The Machine - Stiga CP1 430 Li D48 Manual De Instrucciones

5.3 CUTTING HEIGHT ADJUSTMENT
Do this when the cutting means is stationary.
• Adjustment (See Fig.13.A)
6.

USING THE MACHINE

IMPORTANT For instructions regarding the batteries,
refer to the specific manual.
6.1 PRELIMINARY PROCEDURES
Make sure that the safety key is not inserted in its slot. Place
the machine in a stable horizontal position on the ground.
6.1.1 Preparing the machine before starting work
NOTE This machine can be used to mow lawns in vari-
ous ways.
a. Preparation for grass cutting and collection in
the grass catcher:
1. For side discharge models: make sure that the
guard (Fig. 14.A) is lowered and locked by the safe-
ty lever (Fig. 14.B).
Insert the grass catcher shroud (Fig.14.C).
2.
3. Insert the grass catcher (Fig.14.D).
b. Preparation for grass cutting and rear grass
discharge on the ground:
1. Lift the rear discharge guard (Fig.15.A) and fit the pin
(Fig.15.B).
2. For models with side discharge: make sure that the
guard (Fig. 15.C) is lowered and locked by the safety
lever (Fig. 15.D).
To remove the pin: see Fig.15.A/B.
c. Preparation for grass mowing and chopping
(mulching function):
Lift the rear discharge guard (Fig.16.A) and insert the chute
plug (Fig.16.B) in the discharge opening.For models with
side discharge: make sure that the side discharge guard (Fig.
16.C) is lowered and locked by the safety lever (Fig. 16.D).
To remove the chute plug (Fig.16.E):
d. Preparation for grass cutting and side dis-
charge on the ground:
1. Lift the rear discharge guard (Fig.17.A) and insert the
chute plug (Fig.17.B) in the discharge opening.
2. Slightly push the safety lever (Fig.17.C) and lift the side
discharge guard (Fig.17.D).
3. Insert the side discharge chute (Fig.17.E).
4. Close the side discharge guard (Fig.17.D) so as to lock
the side discharge chute (Fig.17.E).
To remove the side discharge chute:
5. Slightly push the safety lever (Fig.17.C) and lift the side
discharge guard (Fig.17.D).
6. Release the side discharge chute (Fig.17.E).
To remove the chute plug:
1. Lift the rear discharge guard (Fig.17.A).
2. Remove the chute plug (Fig.17.B).
6.2 Safety checks
Always carry out the safety checks before use.
6.2.1 Safety check before every use
• Check the integrity and the correct mounting of all com-
ponents of the machine;
• make sure that all fastening devices are correctly tight-
ened;
• keep all surfaces of the machine clean and dry.
6.2.2 Machine operating test
Action
1. Start the machine
(par. 6.3 ).
2. Enable the cutting
means (par.6.3 ).
3. Release both oper-
ator presence levers
(Fig.23.A).
1. Start the machine
(par. 6.3 ).
2. Operate the drive lever
(par. 5.2.3).
3. Disengage the drive
lever.
Test driving
If any of the results fail to match the indications
provided in the tables, do not use the machine! Contact
an Authorised Service Centre to have it checked and
repaired if necessary.
6.3 START-UP
NOTE Start up the machine on a flat surface without ob-
stacles or high grass.
Open the hatch for accessing the battery compart-
1.
ment (Fig.18.A).
2. Insert the batteries correctly in their housing (Fig. 18.B)
Insert the safety key (Fig.19.B) completely and turn it
3.
to "ON" position.
Press the power button (Fig.20.A).
4.
Engage the cutting means by pressing one of the
5. two operator presence levers (Fig.21.A) against the
handle and then the button (Fig.21.B).
EN - 5
Result
1. The display turns off
and the machine is
ready for use.
The cutting means
2.
should move.
3. The levers should
return automatically
and rapidly to the
neutral position, the
motor must switch off
and the cutting means
must stop within a few
seconds.
1. The display turns off
and the machine is
ready for use.
2. The wheels should
move the machine
forward.
3. The wheels should
stop and the machine
stops moving forward.
No abnormal vibrations.
No abnormal sound.